"CNS " CNS Standards List |
|
CNS 105
2021 Edition Scheduled Information to be Given on Enquiring and Ordering of Electric Machines (Medium and Small Size A.C. Synchronous Motors) 詢價與訂購電機應開列之條款（中小型同步電動機） |
|
|
|
CNS 10880-3
2021 Edition Method of Test for Paint Components - Solvent Insoluble Matter 塗料成分檢驗法–溶劑不溶物 |
|
|
|
CNS 11486
2021 Edition Method of Test for Edgewise Compressive Strength of Corrugated Fiberboard - Butterfly Form Specimen 瓦楞紙板豎壓強度試驗法–蝶形試片 |
|
|
|
CNS 12357
2021 Edition Temperature Limitation of Low Voltage Insulated Wires. 低壓絕緣電線最高容許溫度 |
|
|
|
CNS 4237
2021 Edition Fasteners − Hot dip galvanized coatings 結件－熱浸鍍鋅被覆 |
|
|
|
CNS 3478
2021 Edition Plastic rulers 塑膠鞋 |
Translated |
|
|
CNS 15294
2021 Edition Acoustics - Laboratory measurement of the flanking transmission of airborne and impact sound between adjoining rooms - Application to light elements when the junction has a small influence 聲學－相鄰兩室間空氣音及衝擊音側向傳播之實驗室量測法－應用於連接影響不大之輕型構件 |
|
|
|
CNS 15511-21-2
2021 Edition Electric vehicle conductive charging system − Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supply − EMC requirements for off-board electric vehicle charging systems 電動車輛傳導式充電系統－第21-2部：電動車輛以傳導式連接至交流/直流電源的要求－非車載電動車輛充電系統的電磁相容要求 |
|
|
|
CNS 1002-1-1
2021 Edition Hydrochloric acid for industrial use - Part 1-1: Determination of total acidity - Titrimetric method 工業用氫氯酸－第１－１部：總酸度測定法－中和滴定法 |
|
|
|
CNS 6416
2021 Edition Pinion-type Cutters for Cylindrical Gears; Disc-gear Cutters for Spur Gears 圓柱齒輪用齒輪形切齒刀（正齒輪用鐘形切齒刀） |
|
|
|
CNS 14905-4
2021 Edition Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type 手持型電動工具－安全性－第２－４部：砂光機與拋光機之個別規定（盤式除外） |
|
|
|
CNS 108
2021 Edition Scheduled Information to be Given on Enquiring and Ordering of Electric Machines (Medium and Small Size Transformers) 詢價與訂購電機應開列之條款（中小型變壓器） |
|
|
|
CNS 15256
2021 Edition Acoustics – Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss 聲學－風管消音箱及空氣終端單元之實驗室量測程序－插入損失、氣流噪音及總壓力損失 |
|
|
|
CNS 7747
2021 Edition Method of test for water soluble chlorides in pulp, paper and board (Potentiometric method) 紙漿、紙及紙板水溶性氯化物試驗法(電位滴定分析法) |
|
|
|
CNS 11445-9
2021 Edition Noise limits of rotating electrical machines 旋轉電機之噪音限度 |
|
|
|
CNS 4713
2021 Edition Method of test for ethanol-toluene extractives in wood 木材中乙醇甲苯萃取物試驗法 |
|
|
|
CNS 15530
2021 Edition Methods of environmental test on light emitting diode systems (for general lighting service) 照明用發光二極體系統之環境試驗法 |
|
|
|
CNS 11445-2
2021 Edition Method for determining lossess and efficiency of rotating electrical machinery from test (excluding machines for traction vehicles) 旋轉電機損失與效率試驗法 |
|
|
|
CNS 13746
2021 Edition Unplasticized Polyvinyl Chloride Pipes with Polyethylene Lining for Wastewater and General Uses 污水及一般用內襯聚乙烯之聚氯乙烯塑膠硬質管 |
Translated |
|
|
CNS 13586
2021 Edition Method of Test for Time of Setting of Alumina Cement Mortar(by Vicat Needle) 鋁質水泥墁料凝結時間試驗法（費開氏針法） |
|
|
|
CNS 15407
2021 Edition Instant coffee - Determination of loss in mass at 70 ℃ under reduced pressure 即溶咖啡－70℃減壓下質量損失測定法 |
|
|
|
CNS 1002-1-2
2021 Edition Hydrochloric acid for industrial use - Part 1-2: Determination of total acidity - Potentiometric method 工業用氫氯酸－第１－２部：總酸度測定法－電位差滴定法 |
|
|
|
CNS 14494
2021 Edition Glassfiber reinforced plastic pressure pipe for conveying water works 輸水用玻璃纖維強化塑膠管 |
|
|
|
CNS 3477
2021 Edition Stainless steel wire rods 不銹鋼線料 |
|
|
|
CNS 9272
2021 Edition Steel bars for prestressed concrete 預力混凝土用鋼棒 |
|
|
|
CNS 8755
2021 Edition Method of Test for Thickness or Height of Compacted Bituminous Paving Mixture Specimens 瀝青舖面混合料壓實試體之厚度或高度試驗方法 |
|
|
|
CNS 15077-7
2021 Edition Test conditions for machining centres − Part 7: Accuracy of finished test pieces 切削中心機之檢驗條件－第7部：精加工試件之準確度 |
|
|
|
CNS 15895
2021 Edition BMX bicycles – Safety requirements and test methods 越野自行車(BMX)－安全要求與測試法 |
|
|
|
CNS 7193
2021 Edition Basic Profiles for Milling Cutters of Busher Roller Chains and Roller Chains 滾子鏈輪與套筒鏈輪銑刀基準輪廓 |
|
|
|
CNS 13162
2021 Edition Guide for the proposal of CNS national standards 國家標準建議書格式指引 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [39] [40] [41] [42] [43] [44] [45] |
