"L " CNS Standards List |
|
CNS 832
2021 Edition Cast Iron Pipes for Pressure Lines With TYTON Joints Class B. 壓力管路用鑄鐵管–使用ＴＹＴＯＮ插承口（Ｂ級） |
|
|
|
CNS 4911
2021 Edition Lacquer wood sealers 木器用透明底漆 |
|
|
|
CNS 5527
2021 Edition SymboLs for Sequential Control (Transformers and Rectifiers) 變壓器及整流器順序控制符號 |
|
|
|
CNS 791
2021 Edition Basic Dimensions of 16 kgf/㎠ Ferrous MateriaLs Pipe Flanges 鐵金屬製管凸緣基準尺度（16 kgf/㎠） |
|
|
|
CNS 13388-7
2021 Edition Iron and steeL − ICP atomic emission spectrometric method − Part 7: Determination of boron content − Distillation as trimethyl borate 鐵及鋼－感應耦合電漿發光光譜分析法－第7 部：硼定量法－硼酸三甲酯蒸餾法 |
|
|
|
CNS 14616
2021 Edition Testing method of evaLuation for structural cushioning materials for packaging 包裝用構造體緩衝材料之特性試驗法 |
|
|
|
CNS 15838
2021 Edition FLexible cellular polymeric materials – Polyurethane foam for laminate use 軟質發泡聚合材料－積層用聚胺酯泡棉 |
|
|
|
CNS 7568
2021 Edition Semi - TubuLar Countersunk Head Rivets Nominal Diameters 1.6 to 10mm 短空心平頂埋頭鉚釘，標稱直徑１．６至１０ｍｍ |
|
|
|
CNS 16890-1
2021 Edition Air fiLters for general ventilation − Part 1: Technical specifications, requirements and classification system based upon particulate matter efficiency (ePM) 一般通風用空氣濾網－第1部：基於微粒物質效率之技術規格、要求及分級系統 |
|
|
|
CNS 22776
2021 Edition Footwear − Test methods for accessories: Touch and cLose fasteners − Shear strength before and after repeated closing 鞋類－黏扣帶配件試驗法－反復開合前後之剪切強度 |
|
|
|
CNS 15533-2
2021 Edition Safety requirements for secondary batteries and battery instaLlations - Part 2: Stationary batteries 二次電池及電池安裝之安全性要求－第2部：定置型電池 |
|
|
|
CNS 792
2021 Edition Basic Dimensions of 20 kgf/㎠ Ferrous MateriaLs Pipe Flanges 鐵金屬製管凸緣基準尺度（20 kgf/㎠） |
|
|
|
CNS 10880-26
2021 Edition Method of Test for Paint Components-Quantitative Test of TotaL Zinc in Solvent Insolubles 塗料成分檢驗法–溶劑不溶物中總鋅之定量試驗 |
|
|
|
CNS 15450
2021 Edition Testing method for chemicaL emission rates from electronic equipment 電器設備化學逸散率試驗法 |
|
|
|
CNS 2147
2021 Edition CLassification of Insulating Materials for Electric Machineries and Apparatus 電絕緣材料之分類 |
|
|
|
CNS 15416-1
2021 Edition Furniture - Assessment of ignitabiLity of upholstered furniture - Part 1: Ignition source: smouldering cigarette 家具－包襯家具燃燒性評估試驗法－第1部：燃燒源：悶燒香煙 |
|
|
|
CNS 3006
2021 Edition Inserts in Cutting MateriaL 超硬金屬鑲刀塊 |
|
|
|
CNS 15407
2021 Edition Instant coffee - Determination of Loss in mass at 70 ℃ under reduced pressure 即溶咖啡－70℃減壓下質量損失測定法 |
|
|
|
CNS 14822
2021 Edition ChiLd-resistant packaging – Requirements and testing procedures for reclosable packages 防止幼童開拆之包裝-可重覆包裝之要求與測試程序 |
|
|
|
CNS 306
2021 Edition Whitworth Taps for HoLe, Cylindrical Shank and Square Head 穿透絲公，方頭長圓柱柄，適於韋氏螺孔 |
Translated |
|
|
CNS 15369-2
2021 Edition Secondary batteries for the propuLsion of electric road vehicles – Part 2: Dynamic discharge performance test and dynamic endurance test 電動車輛推進用二次電池組－第2部：動態放電性能試驗與動態耐久性試驗 |
|
|
|
CNS 15371
2021 Edition Certification method of InertiaL Profilers for pavement measurement 鋪面量測用慣性剖面儀驗證法 |
|
|
|
CNS 17225-1
2021 Edition SoLid biofuels − Fuel specifications and classes − Part 1: General requirements 固態生質燃料－燃料規範與等級－第1部:一般要求事項 |
|
|
|
CNS 14278
2021 Edition Method of test for abrasion resistance of geotextiLes (Sand paper/sliding block method) 地工織物抗磨損性試驗法﹝砂紙磨塊法﹞ |
|
|
|
CNS 14232-7
2021 Edition HeaLth Level Seven (HL7) - Part 7: Observation reporting 健康資訊交換第七層協定－第７部：觀察報告 |
|
|
|
CNS 8622
2021 Edition Method of test for fruit and vegetabLe products－Determination of water-insoluble solids 水果及蔬菜製品檢驗法－不溶性固形物之測定 |
|
|
|
CNS 3639
2021 Edition Method of test for edibLe oils and fats－General rules 食用油脂檢驗法－總則 |
|
|
|
CNS 15837
2021 Edition FLexible cellular polymeric materials – Polyvinylchloride foam sheeting 軟質發泡聚合材料－聚氯乙烯發泡薄板 |
|
|
|
CNS 7406
2021 Edition CeLlular plastics and rubbers – Determination of linear dimensions 發泡塑膠及橡膠－線性尺度測定法 |
|
|
|
CNS 10880-23
2021 Edition Method of Test for Paint Components-Quantitative Test of CaLcium Plumbate in Solvent Insolubles 塗料成分檢驗法–溶劑不溶物中鉛酸鈣之定量試驗 |
|
| Find out:14127Items | To Page of: First -Previous-Next -Last | [39] [40] [41] [42] [43] [44] [45] |
