"15 " CNS Standards List |
|
CNS 15127
2018 Edition Methods of test for the concentration of gases produced by burning of joss sticks 香品燃燒所產生之氣體測定法 |
|
|
|
CNS 15489
2018 Edition Methods of measurement on light emitting diode dies for optical and electrical characteristics 發光二極體晶粒之光學與電性量測法 |
|
|
|
CNS 13715
2018 Edition Message Transfer Part (MTP) Signalling Preformance of Signalling System No.7 第七號信號系統訊息轉送部信號效能 |
|
|
|
CNS 14964-15
2018 Edition Wheelchairs - Part 15 : Requirements for information disclosure, documentation and labelling 輪椅－第１５部：資訊宣告、文件與標示之要求 |
|
|
|
CNS 15593-46
2018 Edition Electricity metering − Data exchange for meter reading, tariff and load control – Part 46: Data link layer using HDLC protocol 電力計量－讀表、計費及負載控制之資料交換－第46部：使用HDLC協定之資料鏈路層 |
|
|
|
CNS 15620-2-2
2018 Edition Insulation coordination for equipment within low-voltage system – Part 2-2: Interface considerations – Application guide 低電壓系統下設備之絕緣協調－第2-2 部：介面考量－應用指引 |
|
|
|
CNS 15612
2018 Edition Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 |
|
|
|
CNS 15651-1
2018 Edition Energy performance of lamp controlgear − Part 1: Controlgear for fluorescent lamps − Method of measurement to determine the total input power of controlgear circuits and the efficiency of the controlgear 光源控制裝置之能源效率－第1部： 螢光燈用控制裝置－光源-控制裝置電路 之總輸入功率與控制裝置效率之量測法 |
|
|
|
CNS 15118-1
2018 Edition Photovoltaic (PV) module safety qualification − Part 1: Requirements for construction 太陽光電模組之安全確認－第1部：結構要求 |
|
|
|
CNS 14155
2018 Edition Transmission of non-telephone signals - Frame-synchronous control and indication signals for audiovisual systems 非電話信號之傳輸–視聽系統之訊框同步控制與指示信號 |
|
|
|
CNS 11518
2018 Edition Lifejackets（Non-inflatable） 救生衣（非充氣式） |
|
|
|
CNS 15037-3
2018 Edition Walking aids manipulated by both arms - Requirements and test methods - Part 3: Walking tables 雙臂操作步行輔具－要求及測試法－第３部：附前臂支撐桌助行器 |
|
|
|
CNS 15153
2018 Edition Biological evaluation of medicaldevices - Part 17 : Establishment of allowable limits for leachable substances 醫療器材生物性評估－第１７部：可溶出物質容忍限量之建立 |
|
|
|
CNS 15176-2-1
2018 Edition Wind turbines - Part 2-1 : Design, performance and safety requirements for small vertical axis wind turbines 風力機－第2-1部:小型垂直軸風力機設計、性能及安全要求 |
|
|
|
CNS 15676-3
2018 Edition Interior air of road vehicles − Part 3: Screening method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials − Micro-scale chamber method 道路車輛內部空氣－第3 部：車輛內部零件與材料之揮發性有機化合物逸散量篩檢測定法－微型試驗箱法 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 15395
2018 Edition Green coffee − Determination of loss in mass at 105 ℃ 咖啡生豆－於105 ℃之質量損失測定法 |
|
|
|
CNS 9158
2018 Edition 250V Twin-Core,Three-Core EPR Insulated,CP Sheathed Metal Netting Covered Cable and 250V Twin-Core,Three-Core EPR Insulated Metal Netting Covered PVC Anti-Corrosion Cable for Marine Use 船用２５０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及２５０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 15710-1
2018 Edition Effects of current on human beings and livestock − Part 1: General aspects 電流在人體及家畜上之效應－第1 部：概觀 |
|
|
|
CNS 15176-2
2018 Edition Wind turbines − Part 2: Design requirements for small wind turbines 風力機－第2部： 小型風力機設計要求 |
|
|
|
CNS 15705-1
2018 Edition Tools for pressing – Punch holder shanks – Part 1: Type A 衝壓用工具－衝頭座柄－第1 部：A 型 |
|
|
|
CNS 15609-3
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings 熱塑性塑膠管與管件－衛氏軟化溫度－第3部：丙烯腈-丁二烯-苯乙烯及丙烯腈-苯乙烯-丙烯酸酯管與管件之試驗條件 |
|
|
|
CNS 15620-3
2018 Edition Insulation coordination for equipment within low-voltage system – Part 3: Use of coating, potting or moulding for protection against pollution 低電壓系統下設備之絕緣協調－第3 部：用於污染防護之塗裝、封裝或壓塑 |
|
|
|
CNS 15703-1
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 1: Dimensions and designation of shanks of forms A, AD, AF, U, UD and UF 自動換刀器用7/24 錐度刀柄－第1 部：刀柄型式A、AD、AF、U、UD 及UF 之尺度及標示 |
|
|
|
CNS 15697
2018 Edition Wood – Determination of decay resistance 木材耐腐朽性試驗法 |
|
|
|
CNS 11524
2018 Edition Method of test for windows and doors-general rule 門窗性能試驗法通則 |
|
|
|
CNS 15145
2018 Edition Preparation of steel substrates before application of paints and related products-Surface roughness characteristics of blast-cleaned steel substrates (Method for the grading of surface profile of abrasive blast-cleaned steel-Comparator procedure) 調理肉品 |
|
|
|
CNS 15676-1
2018 Edition Interior air of road vehicles − Part 1: Whole vehicle test chamber − Specification and method for the determination of volatile organic compounds in cabin interiors 道路車輛內部空氣－第1 部：整車試驗室－車廂內部揮發性有機化合物測定法 |
|
|
|
CNS 15660-8
2018 Edition Test conditions for numerically controlled turning machines and turning centres − Part 8: Evaluation of thermal distortions 數值控制車床及車削中心機之試驗條件－第8 部：熱變形之評估 |
|
|
|
CNS 13919
2018 Edition Equipment to perform in-service monitoring on 1544 Kbps signals 服務狀態中監視 1544 Kbps 信號之設備 |
|
| Find out:2250Items | To Page of: First -Previous-Next -Last | [40] [41] [42] [43] [44] [45] [46] |
