"15 " CNS Standards List |
|
CNS 9153
2018 Edition 660V, Twin-Core, Three-Core EPR Insulated PVC Sheathed Metal Netting Covered Cable and 660V Twin-Core, Three-Core EPR Insulated PVC Sheathed Metal Netting Covered PVC Anti-Corrosion Cable for Marine Use 船用６６０Ｖ二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及６６０Ｖ二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 15620-4
2018 Edition Insulation coordination for equipment within low-voltage system – Part 4: Considerationof high-frequency voltage stress 低電壓系統下設備之絕緣協調－第4 部：高頻電壓應力之考量 |
|
|
|
CNS 15176-2-1
2018 Edition Wind turbines - Part 2-1 : Design, performance and safety requirements for small vertical axis wind turbines 風力機－第2-1部:小型垂直軸風力機設計、性能及安全要求 |
|
|
|
CNS 15651-1
2018 Edition Energy performance of lamp controlgear − Part 1: Controlgear for fluorescent lamps − Method of measurement to determine the total input power of controlgear circuits and the efficiency of the controlgear 光源控制裝置之能源效率－第1部： 螢光燈用控制裝置－光源-控制裝置電路 之總輸入功率與控制裝置效率之量測法 |
|
|
|
CNS 11524
2018 Edition Method of test for windows and doors-general rule 門窗性能試驗法通則 |
|
|
|
CNS 15832-2-4
2018 Edition Method of test for coating components − Part 2-4: Component analysis in solvent soluble matter − Alkyd resin 塗料成分試驗法－第2-4部：溶劑可溶物中成分分析－醇酸樹脂 |
|
|
|
CNS 15155
2018 Edition Biological evaluation of medical devices - Part 19 : Physico-chemical, morphological and topographical characterization of materials 醫療器材生物性評估－第１９部：材料之物理化學、形態及拓撲學的特性分析 |
|
|
|
CNS 15404
2018 Edition Roasted ground coffee − Determination of moisture content − Method by determination of loss in mass at 103 ℃ (Routine method) 焙製磨碎咖啡－水分測定－於103 ℃之質量損失測定法(常用法) |
|
|
|
CNS 3515
2018 Edition Cycles − Audible warning devices − Technical specification and test methods 自行車－聲音警告裝置－技術規定及測試法 |
|
|
|
CNS 9154
2018 Edition 660V, Twin-Core, Thre-Core EPR Insulated CP Sheathed Metal Netting Covered Cable and 660V Twin-Core, Three-Core EPR Insulated CP Sheathed Metal Netting Cover PVC Anti-Corrosion Cable for Marine Use 船用６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 15676-2
2018 Edition Interior air of road vehicles − Part 2: Screening method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials − Bag method 道路車輛內部空氣－第2 部：車輛內部零件與材料之揮發性有機化合物逸散量篩檢測定法－採樣袋法 |
|
|
|
CNS 15130-3-10
2018 Edition Tests on electric cables under fire conditions - Part 3-10 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Apparatus 電纜之燃燒試驗－第３－１０部：垂直敷設成束電線電纜之垂直火焰擴散試驗－器材 |
|
|
|
CNS 15660-8
2018 Edition Test conditions for numerically controlled turning machines and turning centres − Part 8: Evaluation of thermal distortions 數值控制車床及車削中心機之試驗條件－第8 部：熱變形之評估 |
|
|
|
CNS 9155
2018 Edition 250V,Single-Core,Twin-Core,Three-Core,EPR Insulated PVC Sheathed Metal Netting Covered Cable and 250V Single-Core, Twin-Core, Three-Core EPR Insulated PVC Sheathed Metal Netting Covered PVC Anti-Corrosion Cable for Marine Use 船用２５０Ｖ單心、二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝電纜（附共同遮蔽）及２５０Ｖ單心、二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附共同遮蔽） |
|
|
|
CNS 15130-3-25
2018 Edition Tests on electric cables under fire conditions - Part 3-25 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Category D 電纜之燃燒試驗－第３－２５部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ｄ |
|
|
|
CNS 11503
2018 Edition Lifebuoy self-igniting lights 救生圈之自燃燈 |
|
|
|
CNS 15127
2018 Edition Methods of test for the concentration of gases produced by burning of joss sticks 香品燃燒所產生之氣體測定法 |
|
|
|
CNS 15612
2018 Edition Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 |
|
|
|
CNS 15620-2-1
2018 Edition Insulation coordination for equipment within low-voltage system – Part 2-1: Application Guide – Dimensioning procedure worksheets and dimensioning examples 低電壓系統下設備之絕緣協調－第2-1 部： 應用指引－ 尺寸量測程序工作表及尺寸量測範例 |
|
|
|
CNS 15405
2018 Edition Roasted ground coffee − Determination of moisture content − Karl Fischer method (Reference method) 焙製磨碎咖啡－水分測定－卡爾費雪法(參考法) |
|
|
|
CNS 15569-2
2018 Edition Hydraulic fluid power – Filter elements – Part 2: Verification of fabrication integrity and determination of the first bubble point 液壓流體動力－過濾器濾心－第2部：查證製作完整性及測定首次起泡點 |
|
|
|
CNS 15130-3-21
2018 Edition Tests on electric cables under fire conditions - Part 3-21 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R 電纜之燃燒試驗－第３－２１部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ａ Ｆ／Ｒ |
|
|
|
CNS 15620-2-2
2018 Edition Insulation coordination for equipment within low-voltage system – Part 2-2: Interface considerations – Application guide 低電壓系統下設備之絕緣協調－第2-2 部：介面考量－應用指引 |
|
|
|
CNS 14151
2018 Edition Line transmission of non-telephone signals - Procedures for establishing communication between threeor more audiovisual terminals using digital channels up to 2Mbit/s 非電話信號之線傳輸–使用可達２Ｍｂｐｓ數位通道建立三部或以上視聽終端機間通訊之程序 |
|
|
|
CNS 15469-2
2018 Edition Tips for assistive products for walking − Requirements and test methods − Part 2: Durability of tips for crutches 步行輔具杖端－要求與試驗方法－第2部：拐杖杖端耐用性 |
|
|
|
CNS 15176-2
2018 Edition Wind turbines − Part 2: Design requirements for small wind turbines 風力機－第2部： 小型風力機設計要求 |
|
|
|
CNS 15652-1
2018 Edition Intelligent lighting systems － Part 1: System function 智慧照明系統－ 第1部：系統功能 |
|
|
|
CNS 15569-3
2018 Edition Hydraulic fluid power - Filter elements - Part 3: Verification of material compatibility with fluids 液壓流體動力－過濾器濾心－第3部：查證材料及流體之相容性 |
|
|
|
CNS 15710-3
2018 Edition Effects of current on human beings and livestock – Part 3: Effects of currents passing through the body of livestock 電流在人體及家畜上之效應－第3 部：電流通過家畜軀體之效應 |
|
| Find out:2250Items | To Page of: First -Previous-Next -Last | [40] [41] [42] [43] [44] [45] [46] |
