"Part " CNS Standards List |
|
CNS 15037-2
2018 Edition Walking aids manipulated by both arms - Requirements and test methods - Part 2: Rollators 雙臂操作步行輔具－要求及測試法－第２部：帶輪助行器 |
|
|
|
CNS 62821-1
2018 Edition Halogen-free, low smoke, thermoplastic insulated and sheathed cables of rated voltages up to and including 450/750 V – Part 1: General requirement 額定電壓450/750 V 以下無鹵素低煙量熱塑性絕緣與被覆電纜－第1部：一般規定 |
|
|
|
CNS 10037
2018 Edition Method of Test for Particle-Size Distribution of Space-Insecticide Aerosol 空間殺蟲劑噴霧粒子大小分布之試驗法 |
|
|
|
CNS 14952-3-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - section 1: calculations using mean values of normally distributed complete data 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第１章：利用常態分配完整資料的平均值進行計算 |
|
|
|
CNS 14213-1
2018 Edition Information technology - Open systems interconnection - Procedures for the operation of OSI registration authorities - Part 1:General procedures 資訊技術–開放系統互連–開放系統互連註冊機構作業程序–第１部：一般程序 |
|
|
|
CNS 15620-3
2018 Edition Insulation coordination for equipment within low-voltage system – Part 3: Use of coating, potting or moulding for protection against pollution 低電壓系統下設備之絕緣協調－第3 部：用於污染防護之塗裝、封裝或壓塑 |
|
|
|
CNS 15620-2-1
2018 Edition Insulation coordination for equipment within low-voltage system – Part 2-1: Application Guide – Dimensioning procedure worksheets and dimensioning examples 低電壓系統下設備之絕緣協調－第2-1 部： 應用指引－ 尺寸量測程序工作表及尺寸量測範例 |
|
|
|
CNS 15593-46
2018 Edition Electricity metering − Data exchange for meter reading, tariff and load control – Part 46: Data link layer using HDLC protocol 電力計量－讀表、計費及負載控制之資料交換－第46部：使用HDLC協定之資料鏈路層 |
|
|
|
CNS 14213-4
2018 Edition Information technology - Open systems interconnection - Procedures for the operation of OSI registration authorities - Part 4: Register of VTE profiles 資訊技術–開放系統互連–開放系統互連註冊機構作業程序–第４部：虛擬終端機環境規範之註冊 |
|
|
|
CNS 13660-2
2018 Edition File Transfer,Access and Management (FTAM)-Part 2:Definition of Type,Constraint Sets and Syntaxes 檔案轉送、存取及管理–第２部分：文件型式限制集合與語法基本定義 |
|
|
|
CNS 15710-4
2018 Edition Effects of current on human beings and livestock – Part 4: Effects of lightning strokes 電流在人體及家畜上之效應－第4 部：雷擊效應 |
|
|
|
CNS 15652-3
2018 Edition Intelligent lighting systems − Part 3: Field area network interface 智慧照明系統－ 第3部：場域網路介面 |
|
|
|
CNS 62821-3
2018 Edition Halogen-free, low smoke, thermoplastic insulated and sheathed cables of rated voltages up to and including 450/750 V – Part 3: Flexible cables (cords) 額定電壓450/750 V 以下無鹵素低煙量熱塑性絕緣與被覆電纜－第3部：可撓式電纜(花線) |
|
|
|
CNS 4394-2
2018 Edition Plastics − Injection moulding of test specimens of thermoplastic materials − Part 1: General principles, and moulding of multipurpose and bar test specimens 塑膠－熱塑性塑膠射出成型試片－第2部：小型拉伸試驗棒 |
|
|
|
CNS 13740-1
2018 Edition Industrial automation systems - Manufacturing message specification - Part 1: Service definition 工業自動化系統–製造訊息規格–第１部：服務定義 |
|
|
|
CNS 15176-2
2018 Edition Wind turbines − Part 2: Design requirements for small wind turbines 風力機－第2部： 小型風力機設計要求 |
|
|
|
CNS 13713
2018 Edition Functional Description of the Message Transfer Part (MTP) Level 2 of Signalling System No.7 第七號信號系統訊息轉送部第２階功能描述 |
|
|
|
CNS 15620-5
2018 Edition Insulation coordination for equipment within low-voltage system – Part 5: Comprehensive method for determining clearance and creepage distances equal to or less than 2 mm 低電壓系統下設備之絕緣協調－第5 部： 決定2 mm 以下空間距離及沿面距離之詳盡方法 |
|
|
|
CNS 15153
2018 Edition Biological evaluation of medicaldevices - Part 17 : Establishment of allowable limits for leachable substances 醫療器材生物性評估－第１７部：可溶出物質容忍限量之建立 |
|
|
|
CNS 14393-6
2018 Edition Biological evaluation of medical devices - Part 6：Tests for local effects after implantation 醫療器材生物性評估－第六部分:植入後的局部效應測試 |
|
|
|
CNS 14393-9
2018 Edition Biological evaluation of medical devices - Part 9: Framework for identification and quantification of potential degradation products 醫療器材生物性評估－第９部：潛在降解產物之鑑別及定量分析架構 |
|
|
|
CNS 15612
2018 Edition Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 |
|
|
|
CNS 12821-1
2018 Edition Identification Cards-Recording Technique-Part 1 : Embossing 識別卡（登錄技術第１部，壓刻） |
|
|
|
CNS 3746-1
2018 Edition Series 1 freight containers - Specification and testing - Part 1：General cargo containers for general purposes 第一類貨櫃－規格與試驗－第１部：通用貨櫃 |
|
|
|
CNS 15606-4
2018 Edition Plastics − Determination of tensile properties − Part 3: Test conditions for films and sheets 塑膠－抗拉性能測定法－第4部：同向與正交異向性纖維強化塑膠複合材料之試驗條件 |
|
|
|
CNS 15609-3
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings 熱塑性塑膠管與管件－衛氏軟化溫度－第3部：丙烯腈-丁二烯-苯乙烯及丙烯腈-苯乙烯-丙烯酸酯管與管件之試驗條件 |
|
|
|
CNS 15176-2-1
2018 Edition Wind turbines - Part 2-1 : Design, performance and safety requirements for small vertical axis wind turbines 風力機－第2-1部:小型垂直軸風力機設計、性能及安全要求 |
|
|
|
CNS 14213-2
2018 Edition Information technology - Open systems interconnection - Procedures for the operation of OSI registration authorities - Part 2: Registration procedures for the OSI document types 資訊技術–開放系統互連–開放系統互連註冊機構作業程序–第２部：開放系統互連文件型式的註冊程序 |
|
|
|
CNS 15652-1
2018 Edition Intelligent lighting systems － Part 1: System function 智慧照明系統－ 第1部：系統功能 |
|
|
|
CNS 15652-4
2018 Edition Intelligent lighting systems − Part 4: Design guide for field area network 智慧照明系統－ 第4部：場域網路設計指引 |
|
| Find out:2535Items | To Page of: First -Previous-Next -Last | [40] [41] [42] [43] [44] [45] [46] |
