"An " CNS Standards List |
|
CNS 623
2020 Edition Method of Test for Sieve Analysis and Water Content of Refractory Material 耐火材料之篩析及含水量之試驗法 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcAnized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 8734
2020 Edition Spices And condiments − Chillies and capsicums, whole or ground (powdered) 香辛料及調味料－全果狀或粉狀番椒與辣椒 |
|
|
|
CNS 6921
2020 Edition Rubber hAndlebar grip for bicycle 自行車用橡膠握套 |
|
|
|
CNS 14626
2020 Edition Cast mAnganese steel crossings for switch and crossing work 錳鋼岔心 |
|
|
|
CNS 9350
2020 Edition Bushes for Plain Bearings with Lubrication Holes And Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 15344
2020 Edition Safety of machinery - Interlocking devices associated with guards - Principles for design And selection 機械安全－防護裝置之聯鎖裝備－設計與選擇原則 |
|
|
|
CNS 3220-1
2020 Edition SAnitary ceramic ware – Tank for water closet 衛生陶瓷器－ 水箱 |
Translated |
|
|
CNS 12235
2020 Edition Series 1 freight containers - HAndling and securing 第一類貨櫃－裝卸及固定 |
|
|
|
CNS 27
2020 Edition TrAnsmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 4486
2020 Edition Fasteners – Surface discontinuities – Bolts, screws And studs for general requirements 螺釘表面瑕疵 |
|
|
|
CNS 625
2020 Edition StAndard Classification of Fireclay Brick 耐火黏土磚分級標準 |
Translated |
|
|
CNS 80000-7
2020 Edition QuAntities and units – Part 7: Light and radiation 量及單位－第7部：光與輻射 |
|
|
|
CNS 15200-5-6
2020 Edition Methods of test for paints – Part 5–6: MechAnical property of film - Adhesion test (Cross–cut test) 塗料一般試驗法－第５－６部：塗膜機械性質：附著試驗(方格法) |
|
|
|
CNS 7921
2020 Edition Method of test for spices And condiments – Determination of acid-insoluble ash 香辛料及調味料之檢驗法－酸不溶性灰分之測定 |
|
|
|
CNS 5038
2020 Edition Laboratory filter paper And method of test 化學分析用濾紙 |
|
|
|
CNS 17296-3
2020 Edition Additive mAnufacturing − General principles − Part 3: Main characteristics and corresponding test methods 積層製造－通則－第3部：主要特性及對應試驗法 |
|
|
|
CNS 2352
2020 Edition StAndard Classification of High-Alumina Brick 高鋁耐火磚分級標準 |
Translated |
|
|
CNS 5561-2
2020 Edition High Tension Cable Connection for Ignition Coils And Distributors for Automobiles 汽車用點火線圈及分電盤用高壓接線端子 |
|
|
|
CNS 2306
2020 Edition White PortlAnd Cement 白色卜特蘭水泥 |
Translated |
|
|
CNS 399
2020 Edition Fastening of Taper Pins And Cotter Pins 定位銷裝配位置（用於圓錐銷及開口銷） |
|
|
|
CNS 8407-2
2020 Edition Test methods for sealing quality of Anodic oxide coatings on aluminium and aluminium alloys - Part 2: Phosphoric-chromic acid solution immersion test method 鋁及鋁合金之陽極氧化膜封孔度試驗法－第２部：磷酸－鉻酸溶液浸漬試驗法 |
|
|
|
CNS 151
2020 Edition Semi - Finished Washers (for Hexagonal Bolts And Nuts: M1 -M20) 半光（輾光）製墊圈（用於六角螺釘及螺帽Ｍ１至Ｍ２０） |
Translated |
|
|
CNS 14143
2020 Edition Methods of chemical Analysis for fine silicon carbide powders for fine ceramics 精密陶瓷用碳化矽微末化學分析法 |
|
|
|
CNS 15232
2020 Edition Oils of lemon And petitgrain citronnier, and oil of lime obtained by a mechanical process - Determination of citral (neral + geranial) content (Gas chromatographic method on capillary columns) 機械程序製檸檬油、檸檬葉油及萊姆油－檸檬油醛（橙花醛＋香葉草醛）含量測定法（毛細管柱氣相層析法） |
|
|
|
CNS 7557
2020 Edition Slip-on Welding Steel Pipe FlAnges (30 kgf/㎠) 滑入熔接式鋼製管凸緣（30 kgf/㎠） |
|
|
|
CNS 4797-6
2020 Edition Safety of toys − Part 6: OrgAnic chemical compounds − Requirements 玩具安全－第6部：有機化合物－要求事項 |
|
|
|
CNS 395
2020 Edition Fillet Radius, Straight Chamfer And Ring Groove (for Bearing Sleeve) 圓角半徑、直倒角、環槽（用於軸承襯） |
|
|
|
CNS 7554
2020 Edition Slip-on Welding Steel Pipe FlAnges (10 kgf/㎠) 滑入熔接式鋼製管凸緣（10 kgf/㎠） |
|
|
|
CNS 15212-3
2020 Edition Clinical Thermometers - Part 3: PerformAnce of compact electrical thermometers（non-predictive and predictive） with maximum device 電子體溫計－第３部：具最大值（非預測性與預測性）裝置之小型電子體溫計的性能 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [46] [47] [48] [49] [50] [51] [52] |
