"an " CNS Standards List |
|
CNS 4240
2020 Edition Electroplated Coating of Bolts, Screws and Nuts 螺栓、螺釘、螺帽之電鍍層 |
|
|
|
CNS 14142
2020 Edition Methods of test for adaptation assessment of fine ceramics under high temperature and high pressure 精密陶瓷高溫、高壓環境適應性試驗法 |
|
|
|
CNS 14294
2020 Edition Method for determination of resistance to sulfuric acid of dense shaped refractory products 緻密定型耐火製品抗硫酸性測定法 |
|
|
|
CNS 11771
2020 Edition General Rules for Allowance of Chemical Analysis and Physical Test 化學分析及物理試驗許可差總則 |
|
|
|
CNS 5270-2
2020 Edition Graphical Symbols for Fluid Power Diagrams-Pump and Motor 液壓、氣壓圖形符號–泵及馬達 |
|
|
|
CNS 61439-4
2020 Edition Low-voltage switchgear and controlgear assemblies − Part 4: Particular requirements for assemblies for construction sites (ACS) 低電壓開關裝置及控制裝置組裝品－第4部：建築工地用組裝品(ACS)之個別要求 |
|
|
|
CNS 1986
2020 Edition Sodium Sulfate, anhydrous 化學試藥（無水硫酸鈉） |
|
|
|
CNS 13137
2020 Edition Safety Standards for Construction of Band Saws With Rollers 送材輪進給式帶鋸機之構造安全基準 |
|
|
|
CNS 395
2020 Edition Fillet Radius, Straight Chamfer and Ring Groove (for Bearing Sleeve) 圓角半徑、直倒角、環槽（用於軸承襯） |
|
|
|
CNS 12616
2020 Edition Method of Test for Electrical Conductivity of Aviation and Distillate Fuels Containing a Static Dissipator Additive 航空燃油含靜電逸散劑導電度測定法 |
|
|
|
CNS 7029
2020 Edition Shape, Dimensions and Travel Angles of Drawbar Eyes for Full Trailers 全拖車用拖桿環首之形狀、尺度及活動範圍 |
|
|
|
CNS 11523
2020 Edition Method of Test for High - Temperature Fiber Blanket Thermal Insulation 高溫絕熱纖維氈檢驗法 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 8156
2020 Edition Edible refined processed oil and fat 食用精製加工油脂 |
|
|
|
CNS 14243
2020 Edition Method of test for smoke point of kerosine and aviation turbine fuels 煤油及航空燃油發煙點試驗法 |
|
|
|
CNS 15212-4
2020 Edition Clinical Thermometers - Part 4: Performance of electrical thermometers for continuous measurement 電子體溫計－第４部：用於連續量測之電子體溫計的性能 |
|
|
|
CNS 10792
2020 Edition Metric Tapered External Screw Threads with Mating Parallel Internal Screw Threads (Nominal Dimensions and Permissible Deviations) 公制推拔外螺紋與配用之平行內螺紋（標稱尺度及公差） |
|
|
|
CNS 11081
2020 Edition Method for Calculating Heat Balancing of Cement Rotary Kiln 水泥工業用窯爐之熱平衡計算方法 |
|
|
|
CNS 8411-1
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Wheel wear test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－ 第１部：磨輪磨耗試驗法 |
|
|
|
CNS 15809
2020 Edition Personal eye-protection – Ultraviolet filters – Transmittance requirements and recommended use 個人眼睛防護具－紫外線濾光鏡－透光度要求及使用 |
|
|
|
CNS 16145-2
2020 Edition Ceramic tiles − Grouts and adhesives − Part 2: Test methods for adhesives 陶瓷面磚－填縫劑與接著劑－第2部：接著劑試驗法 |
|
|
|
CNS 16144-1
2020 Edition Gas detectors − Electrical apparatus for the detection of carbon monoxide in domestic premises − Part 1: Test methods and performance requirements 氣體偵測器－家居處所一氧化碳偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 14579-1
2020 Edition Method of test for prevention of fire for automobiles – Part 1: Fuel tanks 汽車火災預防檢驗法－第１部：燃料箱 |
|
|
|
CNS 15345-1
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 1: Principles and specification for machinery manufacturers 機械安全－降低由機械釋放有害性物質對健康造成之風險－第１部：對機械製造商之原則及規範 |
|
|
|
CNS 4318
2020 Edition ISO Miniature Screw Threads-Tolerances 公制精細小螺紋公差（ＩＳＯ制） |
Translated |
|
|
CNS 7676
2020 Edition Rubber Bumpers of Entrance Doors for Buses 大客車用車門抵門橡膠條 |
|
|
|
CNS 16129-2
2020 Edition Railway applications − Welding of railway vehicles and components − Part 2: Quality requirements and certification of welding manufacturer 鐵路應用－鐵路車輛及其零組件之銲接－第2部：銲接製造廠商品質要求及驗證 |
|
|
|
CNS 14104-3
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 2: Method of describing lower limb amputation stumps 義肢學與矯具學－肢體缺陷－第３部：上肢截肢之描述 |
|
|
|
CNS 8407-2
2020 Edition Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Phosphoric-chromic acid solution immersion test method 鋁及鋁合金之陽極氧化膜封孔度試驗法－第２部：磷酸－鉻酸溶液浸漬試驗法 |
|
|
|
CNS 4539
2020 Edition Terms relating to the manufacture of fasteners 結件詞彙（製造方法） |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [48] [49] [50] [51] [52] [53] [54] |
