"o " CNS Standards List| Method Test | Methods test | Testing methods | Method test | Receiver fire | Stationary training | Wedge Tool | Square Shovels | |
|
CNS 8928
2021 Edition Grooved Pins, Half Length Taper Grooved 槽銷（半長斜底槽） |
|
|
|
CNS 15894
2021 Edition Bicycles − Chain adjusters and crank cotter pins 自行車－鏈條調整器及曲柄插銷 |
|
|
|
CNS 5951
2021 Edition Method of Test for Magnetic Padlocks 磁性掛鎖檢驗法 |
|
|
|
CNS 15912
2021 Edition Design, manufacture, installation and testing of climbing nets and netting/mesh used in amusement rides, devices, play areas and attractions 遊戲場用攀爬網及安全網/格網之設計、製造、安裝及測試 |
|
|
|
CNS 2113-2
2021 Edition Brinell hardness test − Part 2: Table of hardness values 勃氏硬度試驗法－第2部：硬度值表 |
|
|
|
CNS 1494
2021 Edition Method of test for colour fastness to washing and laundering 耐洗染色堅牢度試驗法 |
Translated |
|
|
CNS 8622
2021 Edition Method of test for fruit and vegetable products－Determination of water-insoluble solids 水果及蔬菜製品檢驗法－不溶性固形物之測定 |
|
|
|
CNS 11463
2021 Edition Method of test for fertilizer (General rules) 肥料檢驗法（總則） |
|
|
|
CNS 15416-2
2021 Edition Furniture - Assessment of ignitability of upholstered furniture - Part 2: Ignition source : match-flame equivalent 家具－包襯家具燃燒性評估試驗法－第2部：燃燒源：火柴焰相當物 |
|
|
|
CNS 7567
2021 Edition Semi - Tubular Pan Head Rivets Nominal Diameters 1.6 to 10 mm 短空心盤頭鉚釘（標稱直徑１．６至１０ｍｍ） |
|
|
|
CNS 6985
2021 Edition Polyurethane enamelled round copper winding wires 建築填縫用聚胺酯 |
|
|
|
CNS 15891
2021 Edition Cycles − Screw threads used to assemble freewheels on bicycle hubs 自行車－用於組裝飛輪至輪轂之螺紋 |
|
|
|
CNS 3477
2021 Edition Stainless steel wire rods 不銹鋼線料 |
|
|
|
CNS 15388
2021 Edition Methods of measuring rolling resistance for passenger car, truck and bus tyres − Single point test and correlation of measurement results 小客車、卡客車輪胎滾動阻力量測方法－單點試驗與量測結果相關性 |
|
|
|
CNS 15256
2021 Edition Acoustics – Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss 聲學－風管消音箱及空氣終端單元之實驗室量測程序－插入損失、氣流噪音及總壓力損失 |
|
|
|
CNS 10604
2021 Edition Method of Test for Residual Current Sensing and Relaying Equipment 漏電電驛試驗法 |
|
|
|
CNS 7478
2021 Edition Method of Test for Transparent Synthetic Resin Coating Film of Aluminium Swinging Doors 鋁製推門之透明合成樹脂塗膜檢驗法 |
|
|
|
CNS 13802-11
2021 Edition Graphical symbols for diagrams (Architectural and topographical installation plans and diagrams) 電機工程製圖符號（建築及地形學之裝置圖與製圖） |
|
|
|
CNS 14260
2021 Edition Method of test for measuring nominal thickness of geotextiles and geomenbranes 地工織物及地工防水膜標稱厚度試驗法 |
|
|
|
CNS 792
2021 Edition Basic Dimensions of 20 kgf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度（20 kgf/㎠） |
|
|
|
CNS 5531
2021 Edition Symbols for Sequential Control (Indicating Meters) 計器順序控制符號 |
|
|
|
CNS 15377
2021 Edition Fine ceramics − Ultraviolet light source for testing semiconducting photocatalytic materials 精密陶瓷－紫外線光源用於半導體光觸媒材料測試 |
|
|
|
CNS 3763
2021 Edition Waterproof agent of cement for concrete construction 水泥防水劑 |
|
|
|
CNS 3299-10
2021 Edition Methods of test for ceramic tiles - Part 10: Determination of chemical resistance 陶瓷面磚試驗法－第10部：耐藥品性試驗法 |
|
|
|
CNS 3645
2021 Edition Method of test for edible oils and fats－Determination of refractive index 食用油脂檢驗法－折射率之測定 |
|
|
|
CNS 8359
2021 Edition Mica Plates for Commutator Separators 整流子片用雲母板 |
|
|
|
CNS 11487
2021 Edition Method of Test for Wet Ply Separation of Corrugated Fiberboard 瓦楞紙板濕潤分層試驗法 |
|
|
|
CNS 10793
2021 Edition Roughness Comparison Specimens 表面粗糙度比較標準片 |
|
|
|
CNS 8789
2021 Edition Method of Test for Solvent Resistance of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管耐溶劑性試驗法 |
|
|
|
CNS 2423
2021 Edition Rough rice 稻穀 |
|
| Find out:15086Items | To Page of: First -Previous-Next -Last | [48] [49] [50] [51] [52] [53] [54] |
