CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"15 " CNS Standards List

Z9-General & Miscellaneous
CNS 5151    2017 Edition
Photography-Processing chemicals - Specifications for anhydrous sodium carbonate and sodium carbonate monohydrate
照相術─顯像處理化學品─無水碳酸鈉及一水合碳酸鈉規格
S-Domestic Wares
CNS 15623    2017 Edition
Paragliding equipment – Emergency parachutes – Safety requirements and test methods
飛行傘設備-緊急降落傘-安全要求與試驗法
C-Electrical Engineering
CNS 6152    2017 Edition
Method of Test for Electromechanical Switches(Electrical Endurance)
電機開關檢驗法–電耐久性
C-Electrical Engineering
CNS 11570    2017 Edition
Remote Control Relays and Remote Control Switches
遙控電驛及遙控開關
D-Automotive & Aircraft Engineering
CNS 15481-4    2017 Edition
Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads
道路車輛-電機電子配備環境條件與試驗-第4部:氣候負載
A-Civil Engineering & Architecture
CNS 15520    2017 Edition
Push and Pull Drain Trap (P Type)
建築物室內用補平塗材
Z9-General & Miscellaneous
CNS 5153    2017 Edition
Photography-Processing chemicals-Specifications for potassium bromide
照相術─顯像處理化學品─溴化鉀規格
B-Mechanical Engineering
CNS 15347    2017 Edition
Safety of machinery − General principles for design − Risk assessment and risk reduction
機械安全-設計之一般原則-風險評鑑及風險降低
D-Automotive & Aircraft Engineering
CNS 15513    2017 Edition
Electric road vehicles – Reference energy consumption and range – Test procedures for passenger cars and light commercial vehicles
電動道路車輛-電能消耗與行駛距離-小客車與商用車試驗程序
C-Electrical Engineering
CNS 11573    2017 Edition
Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-50 Sand and Dust Test)
頻率3MHz以下電連接器檢驗法(細砂與塵埃試驗TP–50)
G-Ferrous Materials & Metallurgy
CNS 13154    2017 Edition
Cold rolled special steel strips
冷軋特殊鋼鋼帶
N-Agriculture, Food
CNS 15091-1    2017 Edition
Method of test for deep sea water - Measurement of in-situ temperature
深層海水檢驗法-現場溫度之測量
C-Electrical Engineering
CNS 12153    2017 Edition
Fittings for pliable plastic conduits
合成樹脂可撓電線導管用配件
B-Mechanical Engineering
CNS 1131    2017 Edition
Pliables plastic conduits (replaced by CNS 12152)
夾鉗與剪鉗-拔釘鉗
C-Electrical Engineering
CNS 6150    2017 Edition
Method of Test for Electromechanical Switches(Terminal Temperature Rise)
電機開關檢驗法–端子溫度上昇
Z2-Industry Safety
CNS 16015-2    2017 Edition
Transportation of dangerous goods − Part 2: Dangerous goods list
危險貨物之運輸-第2部:危險貨物表
S-Domestic Wares
CNS 15551-2    2017 Edition
Ergonomics - Accessible design - Sound pressure levels of auditory signals for consumer products
人因工程-無障礙設計 - 消費 產品中聲音訊號之聲壓位準
S-Domestic Wares
CNS 15421    2017 Edition
Office furniture - Chairs
辦公室用椅
K-Chemical Industry
CNS 15832-2-2    2017 Edition
Method of test for coating components − Part 2-2: Component analysis in solvent soluble matter − Softening point (Ring-and-ball method)
塗料成分試驗法-第2-2部:溶劑可溶物中成分分析-軟化點(環與球法)
C-Electrical Engineering
CNS 15511-21    2017 Edition
Electric vehicle conductive charging system – Part 21: Electric vehicle requirements for conductive connection to an a.c./d.c. supply
電動車輛傳導式充電系統-第21部:傳導式連接至a.c./d.c.電源之電動車輛要求
H-Non-ferrous Materials & Metallurgy
CNS 15495    2017 Edition
Test methods of tensile adhesive strength for thermal-sprayed coatings
熔射塗層拉伸附著強度試驗法
C-Electrical Engineering
CNS 11572    2017 Edition
Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-46 Continuity Test)
頻率3MHz以下電連接器檢驗法(連續性試驗TP–46)
K-Chemical Industry
CNS 15832-1-1    2017 Edition
Method of test for coating components − Part 1-1: General rule − Common test conditions
塗料成分試驗法-第1-1部:通則-一般試驗條件
D-Automotive & Aircraft Engineering
CNS 15499-2    2017 Edition
Electrically propelled road vehicles – Safety specifications – Part 2: Vehicle operational safety means and protection against failures
電動推進道路車輛-安全規範-第2部:車輛操作安全方法及故障防護
B-Mechanical Engineering
CNS 4415    2017 Edition
Slotted Countersunk (Oval) Head Screws with Full Dog Point
有槽扁圓頂埋頭長柱端螺釘
C-Electrical Engineering
CNS 15767-2-7    2017 Edition
Plugs and socket-outlets for household and similar purposes − Part 2-7: Particular requirements for cord extension sets
家用和類似用途插頭及插座-第2-7部:延長用電源線組之特定要求
C-Electrical Engineering
CNS 6151    2017 Edition
Method of Test for Electromechanical Switches(Overload)
電機開關檢驗法–過負荷
G-Ferrous Materials & Metallurgy
CNS 15604    2017 Edition
Corrugated stainless steel tubes for water supply
自來水用不銹鋼波狀管

Translated
K-Chemical Industry
CNS 15570    2017 Edition
Petroleum products - Determination of aromatic hydrocarbon types in middle distillates - High performance liquid chromatography method (non-backflush) with refractive index detection
石油產品-中質蒸餾燃油芳香烴類別含量測定法[高效液相層析(非逆洗)/折射率偵檢法]
K-Chemical Industry
CNS 15558-6    2017 Edition
Flexible cellular polymeric materials - Physical properties - Part 6: Determination of burning characteristics
軟質發泡材料-物理特性-第6部:燃燒性測定法

Find out:2250Items   |  To Page of: First -Previous-Next -Last  | [51] [52] [53] [54] [55] [56] [57]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.