"fo " CNS Standards List |
|
CNS 157
2020 Edition Square Taper Washers (for I Sections) 方形推拔墊圈（工字鐵用） |
|
|
|
CNS 15434
2020 Edition Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards 機械安全—防護裝置—設計與建構固定式和移動式防護裝置之一般要求 |
|
|
|
CNS 14670
2020 Edition Method of test for measurement of lubricity of aviation turbine fuels by the ball-on-cylinder lubricity evaluator 航空燃油潤滑度試驗法 |
|
|
|
CNS 29182-7
2020 Edition Information technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 7: Interoperability guidelines 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第7部：互運性指導綱要 |
|
|
|
CNS 9445-1
2020 Edition Sampling procedures for inspection by variables − Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL 計量值檢驗抽樣程序－第1部：單一品質特性與單一允收品質界限(AQL)逐批檢驗依AQL檢索之單次抽樣計畫 |
|
|
|
CNS 154
2020 Edition Large Unfinished Washers (for Metric Bolts and Nuts: M6 - M52) 粗製大墊圈（用於公制螺栓及螺帽Ｍ６至Ｍ５２） |
Translated |
|
|
CNS 15423-1
2020 Edition Equipment for water supply service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 4546
2020 Edition Limits of Sizes and Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: Fine,Tolerances: 4H、5H and 4h)(Diameters from 1 to 300mm and Pitches 0.2 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（細品級–4H、5H、4h）（標稱直徑1至300mm，螺距0.2至6mm） |
|
|
|
CNS 60669-1
2020 Edition Switches for household and similar fixed electrical installations − Part 1: General requirements 家用和類似用途固定式電氣裝置之開關－第1部：一般要求 |
|
|
|
CNS 14505
2020 Edition Method of test for total sulfur in light hydrocarbons,motor fuels and oils by ultraviolet fluorescence 輕質碳氫化合物.汽車燃料及油中總含硫量測定法(紫外線螢光法) |
|
|
|
CNS 22774
2020 Edition footwear − Test methods for accessories: shoe laces − Abrasion resistance 鞋類－配件試驗法－鞋帶耐磨性 |
|
|
|
CNS 158
2020 Edition Rectangular Lock Washers (for Metric Bolts and Nuts: M3 - M52) 長方形防鬆墊圈（用於螺釘及螺帽Ｍ３至Ｍ５２） |
|
|
|
CNS 15355
2020 Edition Test method for determination of mass per unit area of anodic oxide coatings on aluminium and aluminium alloys -Gravimetric method 鋁及鋁合金之陽極氧化膜單位面積質量試驗法－重量分析法 |
|
|
|
CNS 2751
2020 Edition Method of test for volatility of liquefied petroleum gases 液化石油氣揮發性試驗法 |
|
|
|
CNS 531
2020 Edition Iso Metric Screw Threads-Tolerances-Deviations for Constructional Threads 公制螺紋公差（ＩＳＯ制）（結構用螺紋之偏差） |
Translated |
|
|
CNS 11272
2020 Edition Method of Test for Density of Hydraulic Cement 水硬性水泥密度試驗法 |
|
|
|
CNS 16145-3
2020 Edition Ceramic tiles − Grouts and adhesives − Part 3: Terms, definitions and specifications for grouts 陶瓷面磚－填縫劑與接著劑－第3部：填縫劑用語、定義及規範 |
|
|
|
CNS 29182-6
2020 Edition Information technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 6: Applications 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第6部：應用 |
|
|
|
CNS 15795
2020 Edition Information technology − Automatic identification and data capture techniques − Data Carrier Identifiers (including Symbology Identifiers) 資訊技術－自動識別與資料擷取技術－資料載體識別碼(包含符號表示法識別碼) |
|
|
|
CNS 786
2020 Edition Method of Test for Time of Setting of Hydraulic Cement (by Vicat Needle) 水硬性水泥凝結時間檢驗法（費開氏針法） |
|
|
|
CNS 4446
2020 Edition Method of test for determination of water in petroleum products, lubricating oils, and additives by coulometric Karl Fisher titration 石油產品水含量測定法（Ｋａｒｌ Ｆｉｓｃｈｅｒ庫侖法） |
|
|
|
CNS 15353-1
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart scale method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第１部：圖表比例尺法 |
|
|
|
CNS 9227
2020 Edition Woodworking Saw Blades; Technical Specifications for Hand Saw Blades 手工用木工鋸片總則 |
|
|
|
CNS 619
2020 Edition Method of Test for Apparent Porosity, Water Absorption and Specific Gravity of Refractory Bricks 耐火磚視孔隙度、吸水率及比重試驗法 |
|
|
|
CNS 14298
2020 Edition Method of test for determination of benzene, toluene, ethylbenzene, p/m-xylene, o-xylene, C₉ and heavier aromatics, and total aromatics in finished gasoline by gas chromatography 汽油中各種芳香烴測定法（氣相層析法） |
|
|
|
CNS 4544
2020 Edition Limits of sizes and tolerances for ISO metric coarse screw threads (Tolerance quality: medium, tolerances: 5 H、6 H and 6 h、6 g)(Diameters from 1 to 68 mm and pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ＩＳＯ制）（中品級–5Ｈ、6Ｈ、6ｈ、6ｇ）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 15200-5-4
2020 Edition Methods of test for paints – Part 5-4: Mechanical property of film – Scratch hardness (Pencil method) 塗料一般試驗法－第５－４部：塗膜機械性質：刮痕硬度（鉛筆法） |
|
|
|
CNS 14314
2020 Edition Method of test for particle density of fine ceramic powder 精密陶瓷粉末粒子密度測定法 |
|
|
|
CNS 14783
2020 Edition Method of test for benzene in hydrocarbon solvents by gas chromatography 烴類溶劑苯含量氣相層析試驗法 |
|
|
|
CNS 4670-27
2020 Edition Specified Items for Machine Tools - Centerless Grinders 工具機規範之項目–無心磨床 |
Translated |
| Find out:9692Items | To Page of: First -Previous-Next -Last | [53] [54] [55] [56] [57] [58] [59] |
