"3 " CNS Standards List| Basic Environmental | Method test | Electric motor | Test methods | Method test | Information Technology | Methods measurement | Control Cables | |
|
CNS 13751
2019 Edition Method of Test for Sliding Frictional Melting of Woven and Knitted Fabrics 梭織物及針織物摩擦熔融試驗法 |
|
|
|
CNS 5312
2019 Edition Designation Methods for Glass Bulbs of Electric Lamps 照明燈類玻殼之形狀及其代號 |
|
|
|
CNS 15130-2-1
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable – Apparatus 電纜及光纜之燃燒試驗－ 第2-1部：單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 裝置 |
|
|
|
CNS 15176-3
2019 Edition Wind turbines − Part 3: Design requirements for offshore wind turbines 風力機－第3部：離岸風力機 設計要求 |
|
|
|
CNS 13018
2019 Edition Plastic film capacitors (characteristic S) for direct current 塑膠製平墊板 |
|
|
|
CNS 15755-3-4
2019 Edition Conversion tables for units − Part 3-4: Area − Square millimeter and circular mil 單位換算表－第3-4 部：面積－平方毫米與圓密耳 |
|
|
|
CNS 15032
2019 Edition Solar energy - Calibration of field pyrheliometers by comparison to a reference pyrheliometer 太陽能－比較參考日射強度計校正各種場日射強度計 |
|
|
|
CNS 15748-3
2019 Edition Integrated circuits − Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 3: Measurement of radiated emissions – Surface scan method 積體電路－150 kHz 至1 GHz 電磁放射量測－第3 部：輻射放射量測－表面掃描法 |
|
|
|
CNS 5336
2019 Edition Methods of elevated temperature tensile test for iron,steels and heat resisting alloys 鋼鐵及耐熱合金之高溫拉伸試驗法 |
|
|
|
CNS 15094-3
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - Part 3: Removal of toluene 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第3部：甲苯去除性能 |
|
|
|
CNS 5313
2019 Edition Designation Methods for Filament of Incandescent Tungsten Lamps 鎢絲白熾燈之燈絲形狀及其代號 |
|
|
|
CNS 1234
2019 Edition Method of Test for Flexural Strength of Concrete (Using Simple Beam with Center-point Loading) 混凝土抗彎強度試驗法（中心點載重法） |
Translated |
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 15105
2019 Edition Textiles - Determination of abrasion resistance of fabrics by the Martindale method - Part 3 : Determination of mass loss 紡織品耐摩損性馬丁代爾試驗法－第３部：質量減損試驗法 |
|
|
|
CNS 1237
2019 Edition Method of test for mixing water of concrete 混凝土拌和用水試驗法 |
|
|
|
CNS 3004
2019 Edition Shop Test Code of Marine Internal Combustion Engine for Propelling Use 船用內燃主機廠試法 |
|
|
|
CNS 12536
2019 Edition Methods of Chemical Analysis for Tungsten Powder and Tungsten Carbide Powder 鎢粉及碳化鎢粉化學分析法 |
|
|
|
CNS 3-6
2019 Edition Engineering drawing (Symbolic representation of welded joints) 工程製圖(銲接符號表示法) |
|
|
|
CNS 12913
2019 Edition Methods of Test for Cobalt in Nickel Materials for Electron Tubes 電子管用鎳材料中鈷檢驗法 |
|
|
|
CNS 14896-3
2019 Edition Titanium and titanium alloys - Methods for determination of iron content 鈦及鈦合金－鐵定量法 |
|
|
|
CNS 379
2019 Edition Gypsum 石膏 |
|
|
|
CNS 15755-3-2
2019 Edition Conversion tables for units − Part 3-2: Area − Square meter and square yard 單位換算表－第3-2 部：面積－平方公尺與平方碼 |
|
|
|
CNS 21503
2019 Edition Project, programme and portfolio management − Guidance on portfolio management 專案、專案集及專案組合管理−專案集管理指引 |
|
|
|
CNS 14622-3
2019 Edition Sterilization of health care products − Biological indicators − Part 3: Biological indicators for moist heat sterilization processes 健康照護產品滅菌－生物指示劑－第3 部：濕熱滅菌程序之生物指示劑 |
|
|
|
CNS 13752
2019 Edition Method of Test for Knitted Fabrics 針織布試驗法 |
|
|
|
CNS 30
2019 Edition Belt drives − Pulleys − Quality, finish and balance 皮帶傳動－皮帶輪－品質、加工及平衡 |
|
|
|
CNS 10934
2019 Edition Bleed Screw of Hydraulic Brake Wheel Cylinders for Automobiles 汽車用液壓煞車分泵放氣閥 |
|
|
|
CNS 15203
2019 Edition Oils of bergamot, lemon, citron and lime, fully or partially reduced in bergapten - Determination of bergapten content by high-pressure liquid chromatography (HPLC) 香檸檬油、檸檬油、柑橘油及萊姆油－香檸檬烯含量測定高效能液相層析法（ＨＰＬＣ） |
|
|
|
CNS 2739
2019 Edition Method of Long Hill Climbing Test for Automobiles 汽車長坡路試驗法 |
|
|
|
CNS 61347-2-13
2019 Edition Lamp controlgear − Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules 光源控制裝置－第2-13部：LED模組用直流或交流電子式控制裝置之個別要求 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [54] [55] [56] [57] [58] [59] [60] |
