"P " CNS Standards List |
|
CNS 5818
2020 Edition Rubber comPounding ingredients − Carbon black − Determination of iodine adsorption number 橡膠配合劑－碳黑－碘吸附值之測定 |
|
|
|
CNS 60227-6
2020 Edition Polyvinyl chloride inflatable toys (replaced by CNS 4797、CNS 4797-1、CNS 4797-2、CNS 4797-3) 額定電壓450/750 V 以下聚氯乙烯絕緣電纜－第6部：升降機用電纜及可撓式連接用電纜 |
|
|
|
CNS 20889
2020 Edition Printing Specifications for Optical Character Recognition 隱私增強資料去識別化術語與技術分類 |
|
|
|
CNS 1858
2020 Edition Phenylsemicarbazide 化學試藥（苯基胺脲） |
|
|
|
CNS 2751
2020 Edition Method of test for volatility of liquefied Petroleum gases 液化石油氣揮發性試驗法 |
|
|
|
CNS 9445-1
2020 Edition SamPling procedures for inspection by variables − Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL 計量值檢驗抽樣程序－第1部：單一品質特性與單一允收品質界限(AQL)逐批檢驗依AQL檢索之單次抽樣計畫 |
|
|
|
CNS 15423-1
2020 Edition EquiPment for water supply service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 6752
2020 Edition Glossary of Terms Relating to Parts of Metal Sawing Machines 鋸床、切斷機主要零件詞彙 |
|
|
|
CNS 3586
2020 Edition Perlite Heat Insulating Sheet (Block) and Pipe 真珠岩保溫板（磚）及保溫管 |
Translated |
|
|
CNS 14132
2020 Edition Inorganic zinc rich Primer (Water - borne type) 無機鋅粉底漆（水性） |
|
|
|
CNS 9227
2020 Edition Woodworking Saw Blades; Technical SPecifications for Hand Saw Blades 手工用木工鋸片總則 |
|
|
|
CNS 9074
2020 Edition Retaining rings-C tyPe Ｃ型扣環 |
|
|
|
CNS 14490-2
2020 Edition Robots and robotic devices − Safety requirements for industrial robots − Part 2: Robot systems and integration 機器人及機器人裝置－工業機器人之安全要求－第2 部：機器人系統及整合 |
|
|
|
CNS 4446
2020 Edition Method of test for determination of water in Petroleum products, lubricating oils, and additives by coulometric Karl Fisher titration 石油產品水含量測定法（Ｋａｒｌ Ｆｉｓｃｈｅｒ庫侖法） |
|
|
|
CNS 619
2020 Edition Method of Test for APparent Porosity, Water Absorption and Specific Gravity of Refractory Bricks 耐火磚視孔隙度、吸水率及比重試驗法 |
|
|
|
CNS 14783
2020 Edition Method of test for benzene in hydrocarbon solvents by gas chromatograPhy 烴類溶劑苯含量氣相層析試驗法 |
|
|
|
CNS 14104-1
2020 Edition Prosthetics and orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學－肢體缺陷－第１部：先天性肢體缺陷之描述 |
|
|
|
CNS 4546
2020 Edition Limits of Sizes and Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: Fine,Tolerances: 4H、5H and 4h)(Diameters from 1 to 300mm and Pitches 0.2 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（細品級–4H、5H、4h）（標稱直徑1至300mm，螺距0.2至6mm） |
|
|
|
CNS 16145-3
2020 Edition Ceramic tiles − Grouts and adhesives − Part 3: Terms, definitions and specifications for grouts 陶瓷面磚－填縫劑與接著劑－第3部：填縫劑用語、定義及規範 |
|
|
|
CNS 15795
2020 Edition Information technology − Automatic identification and data caPture techniques − Data Carrier Identifiers (including Symbology Identifiers) 資訊技術－自動識別與資料擷取技術－資料載體識別碼(包含符號表示法識別碼) |
|
|
|
CNS 15200-5-4
2020 Edition Methods of test for Paints – Part 5-4: Mechanical property of film – Scratch hardness (Pencil method) 塗料一般試驗法－第５－４部：塗膜機械性質：刮痕硬度（鉛筆法） |
|
|
|
CNS 15353-1
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart scale method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第１部：圖表比例尺法 |
|
|
|
CNS 157
2020 Edition Square TaPer Washers (for I Sections) 方形推拔墊圈（工字鐵用） |
|
|
|
CNS 14314
2020 Edition Method of test for Particle density of fine ceramic powder 精密陶瓷粉末粒子密度測定法 |
|
|
|
CNS 5814
2020 Edition Rubber comPounding ingredients − Carbon black − Determination of loss on heating 橡膠配合劑－碳黑－加熱減量(熱失量)之測定 |
|
|
|
CNS 62498-3
2020 Edition Railway aPplications − Environmental conditions for equipment − Part 3: Equipment for signalling and telecommunications 鐵路應用－設備之環境條件－第3部：號誌及電訊設備 |
|
|
|
CNS 1979
2020 Edition Sodium Phosphate Dibasic, 12 Hydrate 化學試藥（十二水合磷酸–氫鈉） |
|
|
|
CNS 7030
2020 Edition ShaPes and Dimensions of Fifth Wheel Coupling Pins for Semi-trailers 半拖車用第五輪聯結銷之形狀及尺度 |
|
|
|
CNS 4544
2020 Edition Limits of sizes and tolerances for ISO metric coarse screw threads (Tolerance quality: medium, tolerances: 5 H、6 H and 6 h、6 g)(Diameters from 1 to 68 mm and Pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ＩＳＯ制）（中品級–5Ｈ、6Ｈ、6ｈ、6ｇ）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 4547
2020 Edition Limits of Sizes and Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: Medium,Tolerances: 6H and 6h、6g)(Diameters from 2.5 to 300mm and Pitches 0.35 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（中品級–6Ｈ、6ｈ、6ｇ）（標稱直徑2.5至300mm，螺距0.35至6mm） |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [61] [62] [63] [64] [65] [66] [67] |
