"For " CNS Standards List| Alloy Tool | Assembly tools | Phloroglucinol | Test Code | Beltled flange | Conical Taper | Method acceleration | Valves high | |
|
CNS 13138
2020 Edition Safety Standards For Construction of Band Saws With Carriages 送材車式帶鋸機之構造安全基準 |
|
|
|
CNS 7593
2020 Edition Helical Springs Made of Round Wire Dimensions For Cold Coiled Compression Springs of Less Than 0.5 mm Wire Diameter 冷捲成形壓縮螺旋彈簧（簧線直徑小於０．５ｍｍ之構造尺度） |
|
|
|
CNS 148
2020 Edition Taper Shaft End (For Assembling Coupling and Gear) 錐軸梢（用以承裝聯軸器與齒輪） |
|
|
|
CNS 9075
2020 Edition Retaining rings-uniForm section C type Ｃ型同心扣環 |
|
|
|
CNS 52901
2020 Edition Additive manufacturing − General principles − Requirements For purchased AM parts 積層製造－ 通則－ 積層製造之零組件的採購要求 |
|
|
|
CNS 5791
2020 Edition Temperature Indicators For Automobiles 汽車用溫度指示器 |
|
|
|
CNS 15317-3
2020 Edition Crosslinked polyethylene (PE-X) pipe For hot and cold water conveyance - Part 3: Fittings 冷熱水輸送用交連聚乙烯管－第３部：管件 |
|
|
|
CNS 14475
2020 Edition Method of test For estimation of net heat of combustion of aviation fuels 航空燃油淨燃燒熱計算法 |
|
|
|
CNS 61439-4
2020 Edition Low-voltage switchgear and controlgear assemblies − Part 4: Particular requirements For assemblies for construction sites (ACS) 低電壓開關裝置及控制裝置組裝品－第4部：建築工地用組裝品(ACS)之個別要求 |
|
|
|
CNS 14503-1
2020 Edition Evaluation methods For pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 11639
2020 Edition Methods For Measuring Dimensions of Refractory Bricks 耐火磚尺度測定法 |
|
|
|
CNS 15790
2020 Edition Exhaust pipes For burning appliances 燃氣器具用排氣管 |
|
|
|
CNS 14387
2020 Edition Method of test For bending strength of fine ceramic joint 精密陶瓷接合體彎曲強度試驗法 |
|
|
|
CNS 1999
2020 Edition Starch Soluble (For Iodometry) 化學試藥（可溶性澱粉）（碘滴定用） |
|
|
|
CNS 6173
2020 Edition Switches of Lubricating Oil Pressure Warning Lamps For Automobiles 汽車用機油壓力警示燈開關 |
|
|
|
CNS 9568
2020 Edition Adapter Sleeves For Rolling Bearings 滾動軸承套接套筒（附螺帽與鎖緊墊圈） |
|
|
|
CNS 15423-2
2020 Edition Equipment For water supply service– Part 2: Test methods of low temperature resistant 自來水用器具－第2部：耐寒試驗法 |
|
|
|
CNS 362
2020 Edition Spokes For Bicycles 自行車（腳踏車）輻絲 |
Translated |
|
|
CNS 15791
2020 Edition Supply and exhaust pipes For burning appliances 燃氣器具用供排氣管 |
|
|
|
CNS 4486
2020 Edition Fasteners – Surface discontinuities – Bolts, screws and studs For general requirements 螺釘表面瑕疵 |
|
|
|
CNS 14247
2020 Edition Method of test For naphthalene hydrocarbons in aviation turine fuels by ultravioet spectrophotometry 航空燃油中萘族烴試驗法﹝紫外線光譜法﹞ |
|
|
|
CNS 2737
2020 Edition Measurement of the maximum speed For motor vehicles 機動車輛最高速率測定法 |
|
|
|
CNS 9349
2020 Edition Bushes For Plain Bearings Made From Copper Alloys, Solid 滑動軸承軸襯–銅合金製整件 |
|
|
|
CNS 6502
2020 Edition Method of test For spices and condiments – Determination of cold water-soluble extract 香辛料及調味料之檢驗法－冷水萃取物之測定 |
|
|
|
CNS 2392
2020 Edition Trough Type Clay-Burnt Tiles For Building 建築用槽形土燒瓦 |
Translated |
|
|
CNS 3382
2020 Edition Method of test For gum content in fuels by jet evaporation 汽油及航空燃油膠含量試驗法 |
|
|
|
CNS 7680
2020 Edition Shapes and Dimensions of Seats For Buses 大客車用座椅之形狀及尺度 |
|
|
|
CNS 15319-9-1
2020 Edition Sodium hydroxide For industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 8386
2020 Edition Mechanical Fuel Pumps For Automobiles 汽車用機械驅動式燃料泵 |
|
|
|
CNS 158
2020 Edition Rectangular Lock Washers (For Metric Bolts and Nuts: M3 - M52) 長方形防鬆墊圈（用於螺釘及螺帽Ｍ３至Ｍ５２） |
|
| Find out:9607Items | To Page of: First -Previous-Next -Last | [62] [63] [64] [65] [66] [67] [68] |
