"p " CNS Standards List |
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 17296-2
2020 Edition Additive manufacturing − General principles − Part 2: Overview of process categories and feedstock 積層製造－通則－第2部：製程類別及進給料之概述 |
|
|
|
CNS 15355
2020 Edition Test method for determination of mass per unit area of anodic oxide coatings on aluminium and aluminium alloys -Gravimetric method 鋁及鋁合金之陽極氧化膜單位面積質量試驗法－重量分析法 |
|
|
|
CNS 532
2020 Edition Limits of Size and Tolerances for ISO Metric Coarse Screw Threads (Tolerance Quality:Fine,Tolerances:4H、5H and 4h)(Diameters from 1 to 68 mm and pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ISO制）（細品級–4H、5H、4h）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 10019
2020 Edition Rubber, vulcanized or thermoplastic − Determination of compression stress-strain properties 硫化或熱塑性橡膠壓縮應力－應變性質測定法 |
|
|
|
CNS 14315
2020 Edition Methods of test for bending fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 15200-6-1
2020 Edition Methods of test for paints - Part 6-1: Chemical property of film - Resistance to liquids 塗料一般試驗法－第6-1部：塗膜化學性質－耐液體性 |
|
|
|
CNS 9350
2020 Edition Bushes for plain Bearings with Lubrication Holes and Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 60227-6
2020 Edition polyvinyl chloride inflatable toys (replaced by CNS 4797、CNS 4797-1、CNS 4797-2、CNS 4797-3) 額定電壓450/750 V 以下聚氯乙烯絕緣電纜－第6部：升降機用電纜及可撓式連接用電纜 |
|
|
|
CNS 15692-3
2020 Edition Safety of machinery − Laser processing machines − Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2) 機械安全－雷射加工機－第3 部：雷射加工機、手持加工裝置及附屬輔助設備之噪音降低及噪音量測法(準確度等級2) |
|
|
|
CNS 1865
2020 Edition phosphorus Pentoxide 化學試藥（五氧化二磷） |
|
|
|
CNS 157
2020 Edition Square Taper Washers (for I Sections) 方形推拔墊圈（工字鐵用） |
|
|
|
CNS 14103-3
2020 Edition prosthetics and orthotics - Vocabulary - Part 2: Terms relating to external limb prostheses and wearers of these prostheses 義肢學與矯具學－詞彙－第３部：外用矯具之術語 |
|
|
|
CNS 15820-1
2020 Edition Electric motorcycles – Safety specifications – Part 1: Functional safety 電動機車－安全規範－第1 部：功能性安全 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 15373
2020 Edition Liquefied petroleum gases － Determination of dissolved residues (High-temperature gravimetric method) 液化石油氣－可溶殘餘物測定法（高溫重量法） |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical Tolerancing - principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 7817
2020 Edition Chemical Reagent (potassiunβ- Indoleacetate) 化學試藥（β–吲哚基醋酸鉀） |
|
|
|
CNS 61439-2
2020 Edition Low-voltage switchgear and controlgear assemblies − part 2: Power switchgear and controlgear assemblies 低電壓開關裝置及控制裝置組裝品－第2部：電力開關裝置及控制裝置組裝品 |
|
|
|
CNS 3390
2020 Edition Method of test for kinematic viscosity of transparent and opaque liquids (and calculation of dynamic viscosity) 透明與不透明液體黏度試驗法（動黏度及絕對黏度） |
|
|
|
CNS 15232
2020 Edition Oils of lemon and petitgrain citronnier, and oil of lime obtained by a mechanical process - Determination of citral (neral + geranial) content (Gas chromatographic method on capillary columns) 機械程序製檸檬油、檸檬葉油及萊姆油－檸檬油醛（橙花醛＋香葉草醛）含量測定法（毛細管柱氣相層析法） |
|
|
|
CNS 8410-1
2020 Edition Test methods for corrosion resistance of anodic oxide coatings on aluminium and aluminium alloys - part 1: Alkali resistance test 鋁及鋁合金之陽極氧化膜耐蝕性試驗法－第１部：耐鹼性試驗法 |
|
|
|
CNS 8407-2
2020 Edition Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys - part 2: Phosphoric-chromic acid solution immersion test method 鋁及鋁合金之陽極氧化膜封孔度試驗法－第２部：磷酸－鉻酸溶液浸漬試驗法 |
|
|
|
CNS 153
2020 Edition Coarse Type Washers (Primarily for Hexagonal Bolts and Nuts) 粗製墊圈（用於六角螺釘及螺帽） |
Translated |
|
|
CNS 4670-28
2020 Edition Specified Items for Machine Tools - Universal Tool Grinders 工具機規範之項目–萬能工具磨床 |
Translated |
|
|
CNS 4545
2020 Edition Limits of Sizes and Tolerances for ISO Metric Coarse Screw Threads (Tolerance Quality: Coarse,Tolerances: 7H and 8g)(Diameters from 3 to 68mm and pitches 0.5 to 6mm) 公制粗螺紋限界尺寸及公差（ISO制）（粗品級–7H、8g）（標稱直徑3至68mm，螺距0.5至6mm） |
|
|
|
CNS 5270-8
2020 Edition Graphical Symbols for Fluid Power Diagrams-Check Valve 液壓、氣壓圖形符號–止回閥 |
|
|
|
CNS 14104-5
2020 Edition prosthetics and orthotics - Limb deficiencies - Part 4: Description of causal conditions leading to amputation 義肢學與矯具學－肢體缺陷－第５部：截肢病患臨床狀態之描述 |
|
|
|
CNS 1891
2020 Edition potassium hydroxide; solid 化學試藥（碘酸鉀） |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − part 6: Determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [62] [63] [64] [65] [66] [67] [68] |
