"m " CNS Standards List |
|
CNS 15173
2020 Edition Ducted air-conditioners and air-to-air heat pumps - Testing and rating for performance 接風管型空氣調節機及空氣對空氣式熱泵之試驗法及性能等級 |
|
|
|
CNS 29182-7
2020 Edition Information technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 7: Interoperability guidelines 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第7部：互運性指導綱要 |
|
|
|
CNS 14626
2020 Edition Cast manganese steel crossings for switch and crossing work 錳鋼岔心 |
|
|
|
CNS 14145
2020 Edition methods of test for measuring thermal expansion of fine ceramics by thermomechanical analysis 精密陶瓷以熱工分析之熱膨脹測定法 |
|
|
|
CNS 10019
2020 Edition Rubber, vulcanized or thermoplastic − Determination of compression stress-strain properties 硫化或熱塑性橡膠壓縮應力－應變性質測定法 |
|
|
|
CNS 15352
2020 Edition Hard anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之硬質陽極氧化膜 |
|
|
|
CNS 14104-1
2020 Edition Prosthetics and orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學－肢體缺陷－第１部：先天性肢體缺陷之描述 |
|
|
|
CNS 10897
2020 Edition miniature boiler 小型鍋爐 |
|
|
|
CNS 496
2020 Edition ISO metric Screw Threads-Basic Profile (General Purpose) 公制螺紋基準輪廓（ＩＳＯ制） |
Translated |
|
|
CNS 8411-2
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Abrasive jet test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－第２部：噴射磨耗試驗法 |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
|
|
CNS 15443
2020 Edition Sea water mineral concentrate 海水濃縮礦物質液 |
|
|
|
CNS 153
2020 Edition Coarse Type Washers (Primarily for Hexagonal Bolts and Nuts) 粗製墊圈（用於六角螺釘及螺帽） |
Translated |
|
|
CNS 1964
2020 Edition Sodium Fluoride 化學試藥（氟化鈉） |
|
|
|
CNS 3126
2020 Edition Bolts, Screws and Studs-Nominal Lengths, and Thread Lengths 螺栓、螺釘、螺樁之長度及螺紋長度 |
|
|
|
CNS 2519
2020 Edition Railway Sleeper (for 1067 mm Gauge) 鐵路木枕（軌距1067mm者） |
|
|
|
CNS 15193-3
2020 Edition Safety of machinery - Permanent means of access to machinery - Part 3: Stairs,stepladders and guard-rail 機械安全－接近機械之永久性方法－第３部：階梯、踏梯及護欄 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 5561-2
2020 Edition High Tension Cable Connection for Ignition Coils and Distributors for Automobiles 汽車用點火線圈及分電盤用高壓接線端子 |
|
|
|
CNS 13719
2020 Edition Welding consumables − Covered electrodes for mild steel, high tensile strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用鋼用被覆銲條 |
|
|
|
CNS 2393
2020 Edition method of test for whiteness of white portland cement 白色卜特蘭水泥白度檢驗法 |
|
|
|
CNS 15833
2020 Edition Low-emissivity coated glass in building 建築用低輻射鍍膜玻璃 |
|
|
|
CNS 1988
2020 Edition Sodium sulfide nonahydrate (Reagent) 九水合硫化鈉（試藥） |
|
|
|
CNS 470
2020 Edition Testing Standard for Cement Roof Tiles 水泥瓦檢驗標準 |
Translated |
|
|
CNS 7070
2020 Edition method of test for spices and condiments – Determination of moisture content – Entrainment method 香辛料及調味料之檢驗法－水分含量之測定(蒸餾法) |
|
|
|
CNS 14596
2020 Edition Welding consumables − Gas shielded and self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
|
|
CNS 2352
2020 Edition Standard Classification of High-Alumina Brick 高鋁耐火磚分級標準 |
Translated |
|
|
CNS 61850-5
2020 Edition Communication networks and systems for power utility automation − Part 5: Communication requirements for functions and device models 電力公用事業自動化之通訊網路及系統－第5部：功能及裝置模型之通訊要求事項 |
|
|
|
CNS 3590
2020 Edition method of Test for Normal Consisteney of Hydraulic Cement 水硬性水泥之正常稠度檢驗法 |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [71] [72] [73] [74] [75] [76] [77] |
