"M " CNS Standards List |
|
CNS 15355
2020 Edition Test Method for determination of mass per unit area of anodic oxide coatings on aluminium and aluminium alloys -Gravimetric method 鋁及鋁合金之陽極氧化膜單位面積質量試驗法－重量分析法 |
|
|
|
CNS 3390
2020 Edition Method of test for kinematic viscosity of transparent and opaque liquids (and calculation of dynamic viscosity) 透明與不透明液體黏度試驗法（動黏度及絕對黏度） |
|
|
|
CNS 4547
2020 Edition LiMits of Sizes and Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: Medium,Tolerances: 6H and 6h、6g)(Diameters from 2.5 to 300mm and Pitches 0.35 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（中品級–6Ｈ、6ｈ、6ｇ）（標稱直徑2.5至300mm，螺距0.35至6mm） |
|
|
|
CNS 15820-2
2020 Edition Electric Motorcycles − Safety specifications − Part 2: Protection against hydrogen hazards for motorcycles fuelled with compressed hydrogen 電動機車－安全規範－第2 部：防止氫氣危害 |
|
|
|
CNS 4544
2020 Edition LiMits of sizes and tolerances for ISO metric coarse screw threads (Tolerance quality: medium, tolerances: 5 H、6 H and 6 h、6 g)(Diameters from 1 to 68 mm and pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ＩＳＯ制）（中品級–5Ｈ、6Ｈ、6ｈ、6ｇ）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 15817
2020 Edition Edible caMellia seed oil 食用苦茶油(油茶油) |
|
|
|
CNS 15787
2020 Edition Method of fillet weld test for welding consumables 銲接材料之填角銲試驗法 |
|
|
|
CNS 4670-27
2020 Edition Specified IteMs for Machine Tools - Centerless Grinders 工具機規範之項目–無心磨床 |
Translated |
|
|
CNS 8410-1
2020 Edition Test Methods for corrosion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Alkali resistance test 鋁及鋁合金之陽極氧化膜耐蝕性試驗法－第１部：耐鹼性試驗法 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test Methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 1959
2020 Edition TrisodiuM citrate dihydrate (Reagent) 二水合檸檬酸三鈉（試藥） |
|
|
|
CNS 1811
2020 Edition Mercury 化學試藥（汞） |
|
|
|
CNS 7921
2020 Edition Method of test for spices and condiments – Determination of acid-insoluble ash 香辛料及調味料之檢驗法－酸不溶性灰分之測定 |
|
|
|
CNS 15319-9-1
2020 Edition SodiuM hydroxide for industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 15423-1
2020 Edition EquipMent for water supply service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 9300
2020 Edition CheMical Reagent ( Polyviny Alcohol ) 化學試藥（聚乙烯醇） |
|
|
|
CNS 29182-7
2020 Edition InforMation technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 7: Interoperability guidelines 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第7部：互運性指導綱要 |
|
|
|
CNS 5700
2020 Edition Glossary of TerMs for Rolling Bearings 滾動軸承名詞 |
|
|
|
CNS 9480
2020 Edition Tyres - Coast-by Methods for measurement of tyre-to-road sound emission 輪胎實車慣性滑行噪音測定法 |
|
|
|
CNS 15352
2020 Edition Hard anodic oxide coatings on aluMinium and aluminium alloys 鋁及鋁合金之硬質陽極氧化膜 |
|
|
|
CNS 10019
2020 Edition Rubber, vulcanized or therMoplastic − Determination of compression stress-strain properties 硫化或熱塑性橡膠壓縮應力－應變性質測定法 |
|
|
|
CNS 5790
2020 Edition Hazard Warning Signal Flashers for AutoMobiles 汽車用危險警示信號燈閃光器 |
Translated |
|
|
CNS 8734
2020 Edition Spices and condiMents − Chillies and capsicums, whole or ground (powdered) 香辛料及調味料－全果狀或粉狀番椒與辣椒 |
|
|
|
CNS 14596
2020 Edition Welding consuMables − Gas shielded and self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
|
|
CNS 3589
2020 Edition Air-Entraining Additions for Use in The Manufacture of Air-Entraining Portland Cement 輸氣卜特蘭水泥製造用輸氣添加劑 |
|
|
|
CNS 8987
2020 Edition CheMical Reagent(Acidity and Alkalinity Determination) 化學試藥（酸鹼性之檢驗） |
|
|
|
CNS 8411-1
2020 Edition Test Methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Wheel wear test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－ 第１部：磨輪磨耗試驗法 |
|
|
|
CNS 27
2020 Edition TransMission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 10895
2020 Edition Vocabulary of Metrology − Basic and general concepts and associated terms (VIM) 計量學詞彙－基本與一般概念及相關用語 |
|
|
|
CNS 15566-1
2020 Edition Safety of Machinery – Pressure-sensitive protective devices – Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors 機械安全－壓敏保護裝置－第1 部：設計及測試壓敏墊及壓敏底板之一般原則 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [72] [73] [74] [75] [76] [77] [78] |
