"d " CNS Standards List |
|
CNS 11278
2020 Edition End-hardened Rails 端部熱處理鋼軌 |
|
|
|
CNS 15352
2020 Edition Hard anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之硬質陽極氧化膜 |
|
|
|
CNS 17011
2020 Edition Conformity assessment – Requirements for accreditation bodies accrediting conformity assessment bodies 符合性評鑑－認證機構認證符合性評鑑機構之要求事項 |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
|
|
CNS 14783
2020 Edition Method of test for benzene in hydrocarbon solvents by gas chromatography 烴類溶劑苯含量氣相層析試驗法 |
|
|
|
CNS 15193-3
2020 Edition Safety of machinery - Permanent means of access to machinery - Part 3: Stairs,stepladders and guard-rail 機械安全－接近機械之永久性方法－第３部：階梯、踏梯及護欄 |
|
|
|
CNS 3590
2020 Edition Method of Test for Normal Consisteney of Hydraulic Cement 水硬性水泥之正常稠度檢驗法 |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − Part 6: determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
|
|
CNS 16145-3
2020 Edition Ceramic tiles − Grouts and adhesives − Part 3: Terms, definitions and specifications for grouts 陶瓷面磚－填縫劑與接著劑－第3部：填縫劑用語、定義及規範 |
|
|
|
CNS 1891
2020 Edition Potassium hydroxide; solid 化學試藥（碘酸鉀） |
|
|
|
CNS 496
2020 Edition ISO Metric Screw Threads-Basic Profile (General Purpose) 公制螺紋基準輪廓（ＩＳＯ制） |
Translated |
|
|
CNS 7070
2020 Edition Method of test for spices and condiments – Determination of moisture content – Entrainment method 香辛料及調味料之檢驗法－水分含量之測定(蒸餾法) |
|
|
|
CNS 395
2020 Edition Fillet Radius, Straight Chamfer and Ring Groove (for Bearing Sleeve) 圓角半徑、直倒角、環槽（用於軸承襯） |
|
|
|
CNS 14145
2020 Edition Methods of test for measuring thermal expansion of fine ceramics by thermomechanical analysis 精密陶瓷以熱工分析之熱膨脹測定法 |
|
|
|
CNS 12035
2020 Edition Writing boards for educational institutions − Ergonomic, technical and safety requirements and their test methods 教育機構用書寫板－人因工程、技術及安全之要求事項與其試驗法 |
|
|
|
CNS 29182-7
2020 Edition Information technology − Sensor networks: Sensor Network Reference Architecture (SNRA) − Part 7: Interoperability guidelines 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第7部：互運性指導綱要 |
|
|
|
CNS 10019
2020 Edition Rubber, vulcanized or thermoplastic − Determination of compression stress-strain properties 硫化或熱塑性橡膠壓縮應力－應變性質測定法 |
|
|
|
CNS 14306-1
2020 Edition Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates (Method for the calibration of ISO surface profile comparators and for the determination of surface pro 塗料及有關製品塗裝前之鋼面處理－噴射清理鋼面之表面粗糙度特性（磨料噴射清理表面評估用ISO表面輪廓參比標準板之規範及意義） |
|
|
|
CNS 5270-2
2020 Edition Graphical Symbols for Fluid Power Diagrams-Pump and Motor 液壓、氣壓圖形符號–泵及馬達 |
|
|
|
CNS 14784
2020 Edition Method of test for trace benzene in hydrocarbon solvents by capillary gas chromatography 石油溶劑微量苯試驗法（毛細管柱氣相層析法） |
|
|
|
CNS 14104-1
2020 Edition Prosthetics and orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學－肢體缺陷－第１部：先天性肢體缺陷之描述 |
|
|
|
CNS 619
2020 Edition Method of Test for Apparent Porosity, Water Absorption and Specific Gravity of Refractory Bricks 耐火磚視孔隙度、吸水率及比重試驗法 |
|
|
|
CNS 16145-2
2020 Edition Ceramic tiles − Grouts and adhesives − Part 2: Test methods for adhesives 陶瓷面磚－填縫劑與接著劑－第2部：接著劑試驗法 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 15200-4-5
2020 Edition Methods of test for paints - Part 4-5: Visual characteristics of film - Colorimetry (Calculation of colour differences) 塗料一般試驗法－第４－５部：塗膜視覺特性－測色（色差計算） |
|
|
|
CNS 531
2020 Edition Iso Metric Screw Threads-Tolerances-Deviations for Constructional Threads 公制螺紋公差（ＩＳＯ制）（結構用螺紋之偏差） |
Translated |
|
|
CNS 14666
2020 Edition Method of test for vapor pressure of petroleum products (mini method) 石油產品蒸氣壓試驗法（迷你法） |
|
|
|
CNS 1881
2020 Edition Potassium Carbonate, Anhydrous 氯酸鉀（試藥） |
|
|
|
CNS 6921
2020 Edition Rubber handlebar grip for bicycle 自行車用橡膠握套 |
|
|
|
CNS 14596
2020 Edition Welding consumables − Gas shielded and self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [75] [76] [77] [78] [79] [80] [81] |
