"T " CNS Standards List| Personal fall | Edible camellia | Method Test | Raw milk | Illuminance Meters | Steel steel | Phthalic Anhydride | Shell head | |
|
CNS 15284
2020 Edition Rims for Truck and bus 卡車及大客車用輪圈 |
|
|
|
CNS 787
2020 Edition MeThod of Test for Air Content of Hydraulic Cement Mortar 水硬性水泥墁料之空氣含量檢驗法 |
|
|
|
CNS 2788
2020 Edition Fish PlaTes for Light Rails 輕型鋼軌用魚尾板 |
|
|
|
CNS 14501
2020 Edition LighTing and signalling devices for motorcycles 機器腳踏車燈光信號裝置 |
|
|
|
CNS 5814
2020 Edition Rubber compounding ingredienTs − Carbon black − Determination of loss on heating 橡膠配合劑－碳黑－加熱減量(熱失量)之測定 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 153
2020 Edition Coarse Type Washers (Primarily for Hexagonal Bolts and Nuts) 粗製墊圈（用於六角螺釘及螺帽） |
Translated |
|
|
CNS 14964-22
2020 Edition Wheelchair − ParT 22: Set-up procedures 輪椅－第22部：設定程序 |
|
|
|
CNS 6752
2020 Edition Glossary of Terms Relating to Parts of Metal Sawing Machines 鋸床、切斷機主要零件詞彙 |
|
|
|
CNS 14298
2020 Edition MeThod of test for determination of benzene, toluene, ethylbenzene, p/m-xylene, o-xylene, C₉ and heavier aromatics, and total aromatics in finished gasoline by gas chromatography 汽油中各種芳香烴測定法（氣相層析法） |
|
|
|
CNS 6910
2020 Edition Cable Terminals of Storage Battery for Automobiles (Type BE) 汽車用蓄電池翼形螺帽電線端子（ＢＥ型） |
|
|
|
CNS 14315
2020 Edition MeThods of test for bending fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 3458
2020 Edition MeThod of Test for Early Stiffening of Portland Cement (Paste Method) 卜特蘭水泥假凝結檢驗法（水泥漿法） |
|
|
|
CNS 614
2020 Edition MeThod of Test for Size and Bulk Density of Refractory Brick and Insulating Firebrick 耐火磚及絕熱耐火磚之尺度及體密度之試驗法 |
|
|
|
CNS 15269
2020 Edition ProsTheses - Structural testing of hip units 義肢學－下肢義肢結構測試－要求與測試方法 |
|
|
|
CNS 3390
2020 Edition MeThod of test for kinematic viscosity of transparent and opaque liquids (and calculation of dynamic viscosity) 透明與不透明液體黏度試驗法（動黏度及絕對黏度） |
|
|
|
CNS 1559
2020 Edition Diammonium hydrogenphosphaTe (reagent) 化學試藥（磷酸氫二銨） |
|
|
|
CNS 786
2020 Edition MeThod of Test for Time of Setting of Hydraulic Cement (by Vicat Needle) 水硬性水泥凝結時間檢驗法（費開氏針法） |
|
|
|
CNS 14637-6
2020 Edition Test code for machine tools − Part 6: Determination of positioning accuracy on body and face diagonals (Diagonal displacement tests) 工具機試驗規範－第6 部:體與面對角線定位精度之決定(對角線位移試驗) |
|
|
|
CNS 2456-3
2020 Edition PlasTics piping systems for water supply and for drainage and sewerage under pressure − Polyethylene (PE) − Part 2: Pipes 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 14143
2020 Edition MeThods of chemical analysis for fine silicon carbide powders for fine ceramics 精密陶瓷用碳化矽微末化學分析法 |
|
|
|
CNS 14293
2020 Edition Pyrogallol Pyrogallic Acid 1,2,3-Trihydroxybenzene 實驗室用參考示溫錐 |
|
|
|
CNS 11975
2020 Edition MeThod of Test for the Rate of Linear Change of Castable Refractories 可鑄耐火材料熱脹縮試驗法 |
|
|
|
CNS 12684
2020 Edition QualiTy management − Quality of an organization − Guidance to achieve sustained success 品質管理－組織之品質－達成永續成功之指引 |
|
|
|
CNS 15193-3
2020 Edition SafeTy of machinery - Permanent means of access to machinery - Part 3: Stairs,stepladders and guard-rail 機械安全－接近機械之永久性方法－第３部：階梯、踏梯及護欄 |
|
|
|
CNS 13169
2020 Edition SafeTy Standards for Construction of Veneer Lathes 單板旋切機之構造安全基準 |
|
|
|
CNS 8049
2020 Edition Spices and condimenTs − Curry powder 香辛料及調味料－咖哩粉 |
|
|
|
CNS 15353-2
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Instrumental method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第２部：儀器測定法 |
|
|
|
CNS 14746
2020 Edition MeThod of test for determining water separation characteristics of aviation turbine fuels by portable separometer 航空燃油水分離性測定法(可攜帶式微水分離器法) |
|
|
|
CNS 13719
2020 Edition Welding consumables − Covered elecTrodes for mild steel, high tensile strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用鋼用被覆銲條 |
|
| Find out:15111Items | To Page of: First -Previous-Next -Last | [83] [84] [85] [86] [87] [88] [89] |
