"D " CNS Standards List |
|
CNS 14503-1
2020 Edition Evaluation methoDs for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 14242
2020 Edition MethoD of test for peroxide number of aviation turbine fuels 航空燃油過氧化物值測定法 |
|
|
|
CNS 4242
2020 Edition WiDths Across Flats and Widths Across Corners for Bolts, Screws and Nuts 螺栓、螺釘、螺帽之對面寬度及對角寬度 |
|
|
|
CNS 7676
2020 Edition Rubber Bumpers of Entrance Doors for Buses 大客車用車門抵門橡膠條 |
|
|
|
CNS 16145-4
2020 Edition Ceramic tiles − Grouts anD adhesives − Part 4: Test methods for grouts 陶瓷面磚－填縫劑與接著劑－第4部：填縫劑試驗法 |
|
|
|
CNS 12843
2020 Edition ChlorosulfonateD Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 8954
2020 Edition WinDscreen Wiper for Automobiles; Bushing 汽車擋風玻璃雨刷用軸襯 |
|
|
|
CNS 1870
2020 Edition Picks, Two Taper EnDs 化學試藥（苦味酸） |
|
|
|
CNS 7553
2020 Edition Slip-on WelDing Steel Pipe Flanges (5 kgf/㎠) 滑入熔接式鋼製管凸緣（5 kgf/㎠） |
|
|
|
CNS 2392
2020 Edition Trough Type Clay-Burnt Tiles for BuilDing 建築用槽形土燒瓦 |
Translated |
|
|
CNS 469
2020 Edition Flat RiDge Type Cement Tiles 平脊形水泥瓦 |
Translated |
|
|
CNS 13269
2020 Edition Safety StanDards for Construction of Rip Saw and Gang Rip Saw 單片縱鋸機及多片縱鋸機之構造安全基準 |
|
|
|
CNS 7559
2020 Edition Basic Dimensions of Copper Alloy Pipe Flanges 銅合金製管凸緣基準尺度 |
|
|
|
CNS 4797-10
2020 Edition Safety of toys − Part 10: Age Determination guidelines 玩具安全－第10部：適用年齡指導綱要 |
|
|
|
CNS 4238
2020 Edition Finishes anD Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical Tolerancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 4354
2020 Edition Finishes anD tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 9567
2020 Edition WithDrawal Sleeves for Rolling Bearings 滾動軸承拔出套筒 |
|
|
|
CNS 15227
2020 Edition Single-use meDical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 2762
2020 Edition MethoD of test for freezing points of high-purity hydrocarbons 高純度烴類凝固點試驗法 |
|
|
|
CNS 3564-2
2020 Edition Rubber, vulcanizeD or thermoplastic − Determination of low-temperature properties − Part 2: Determination of low-temperature brittleness 硫化或熱塑性橡膠－低溫性質之測定－第2部：低溫脆性測定法 |
|
|
|
CNS 616
2020 Edition MethoD of Test for Cold Crushing Strength of Refractory Bricks 耐火磚抗壓強度試驗法 |
|
|
|
CNS 120
2020 Edition Collar (Using Light Duty Set Screw) 頸圈（用螺絲銷、輕型） |
|
|
|
CNS 16146-1
2020 Edition Textile chilD care articles − Safety requirements and test methods for children's cot duvets − Part 1: Duvet (excluding duvet covers) 紡織類兒童照護用品－嬰兒床用被子安全要求與試驗法－第1部：被子(不包括被套) |
|
|
|
CNS 15804
2020 Edition Oil of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 15200-4-1
2020 Edition MethoDs of test for paints - Part 4-1: Visual characteristics of film - Hiding power 塗料一般試驗法－第４－１部：塗膜視覺特性－遮蓋力 |
|
|
|
CNS 14772
2020 Edition MethoDs of test for aromatics in mineral spirits by gas chromatography 礦物型溶劑芳香烴檢驗法（氣相層析法） |
|
|
|
CNS 79
2020 Edition Minimum Distance Across Hexagonal Bolts 螺釘間之最小距離（適用於六角螺釘及螺帽） |
|
|
|
CNS 5270-1
2020 Edition Graphical Symbols for FluiD Power Dizgrams-Line and Connection 液壓、氣壓圖形符號–管路及連接 |
|
|
|
CNS 10016-1
2020 Edition Rubber, vulcanizeD or thermoplastic − Determination of dynamic properties − Part 1: General guidance 硫化或熱塑性橡膠動態性質之測定第1部：一般指引 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [86] [87] [88] [89] [90] [91] [92] |
