"IT " CNS Standards List |
|
CNS 1488
2017 Edition Knife SwITches (With Cover) 有蓋閘刀開關 |
Translated |
|
|
CNS 11875
2017 Edition Fixed Mica CapacITors (Type CM 50) 雲母固定電容器（ＣＭ５０型） |
|
|
|
CNS 9114
2017 Edition Symbols of Television and Broadcast Equipment of Interior Wiring Diagram for ArchITectural Plans 屋內配線設計圖電視、播音類符號 |
|
|
|
CNS 209
2017 Edition Long Drills wITh Square Taper Shank 方錐柄長鑽頭 |
Translated |
|
|
CNS 4589
2017 Edition General Rules of Fixed CapacITors for Use in Electronic Equipment 電子設備用固定電容器通則 |
|
|
|
CNS 14181
2017 Edition Measurement methods for the performance of analog video laser transmITter and receiver modules used for optical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之性能量測法 |
|
|
|
CNS 7285
2017 Edition Method for Determination of Gold and Silver in Ores wITh Tellurium 含碲礦中金及銀定量法 |
|
|
|
CNS 14179
2017 Edition ReliabilITy tests for digital transmitter and receiver modules used for optical fiber communication 光纖通信用數位傳輸和接收模組之可靠度測試 |
|
|
|
CNS 13811
2017 Edition Numerical-Type Reflectors for Light EmITting Diodes 發光二極體數字型反射套板 |
|
|
|
CNS 4356
2017 Edition Slotted Pan Head Screws wITh Large Head 有槽大盤頭螺釘 |
Translated |
|
|
CNS 14182
2017 Edition ReliabilITy and lot control tests for analog video laser transmitter and receiver modules used for optical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 5003
2017 Edition Assembly tools for screws and nuts-Hexagon drive ends for hand -and machine-operated screwdriver bITs 螺釘及螺帽之裝配工具–起子頭六角驅動頭 |
|
|
|
CNS 4844
2017 Edition Heavy Type Hexagon Head Pipe Plugs wITh Shoulder, Vent Hole and Parallel Thread 重型六角頭管塞（具肩部、通氣孔與平行螺紋） |
|
|
|
CNS 5820
2017 Edition Silica Powder (WhITe Carbon) (for Rubber Use) 二氧化矽粉（橡膠用） |
Translated |
|
|
CNS 3598
2017 Edition Plain Bearings, FITs 普通銑刀 |
Translated |
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings wITh Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 4364
2017 Edition Hexagon Head FITting Bolts with Long Threaded Portion 六角頭配合螺栓（具長螺紋部份） |
|
|
|
CNS 13808
2017 Edition EpITaxial Wafers for Light Emitting Diodes 發光二極體磊晶片 |
|
|
|
CNS 15210-6
2017 Edition Information technology - Radio frequency identification for ITem management - Part 6: Parameters for air interface communications at 860MHz to 960MHz 資訊技術─品項管理之無線射頻識別─第６部：８６０ＭＨｚ至９６０ＭＨｚ空中介面通信參數 |
|
|
|
CNS 13507
2017 Edition Methods of Test for Glass - Fibor - Reinferced Plastic Pipe FITtings 玻璃纖維強化塑膠管配件檢驗法 |
Translated |
|
|
CNS 3416
2017 Edition Safety Code for Power Presses (DefinITions) 動力壓機安全規章（定義） |
|
|
|
CNS 501
2017 Edition ISO Metric Fine Screw Threads (Diameters From 8 to 30mm and PITches 1 to 1.25mm) 公制細螺紋4（ISO制）（標稱直徑8至30公釐，螺距1至1.25公釐） |
|
|
|
CNS 10123
2017 Edition Method for Determining Phosphorus Content in Natural and Artificial CryolITe and Aluminium Fluoride for Industrial Use (Reduced Molybdophosphate Photometric Method) 天然及人造冰晶石與工業用氟化鋁中磷定量法（還原鉬磷酸鹽吸光光度法） |
|
|
|
CNS 11572
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-46 ContinuITy Test) 頻率３ＭＨｚ以下電連接器檢驗法（連續性試驗ＴＰ–４６） |
|
|
|
CNS 129
2017 Edition Morse Taper Gauge wITh Flat Head 莫氏圓錐量規（有扁頭） |
|
|
|
CNS 13804
2017 Edition Guidance on the Use of the SubstITution Method for Measurements of Radiation from Microwave Ovens for Frequencies above 1 GHz 應用置換法測量微波爐１ＧＨｚ以上之輻射指引 |
Translated |
|
|
CNS 5507
2017 Edition Rolling Bearings; Bearing wITh Spherical Outside Surface and Extended Inner Ring Width, Insert bearings 嵌入夾緊滾動軸承（具球面外環與加寬內環） |
|
|
|
CNS 12865-9
2017 Edition Method of Test for DigITal Microelectronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 3607
2017 Edition Single Angle Milling Cutters wITh Threaded Holes 附螺紋孔單側角銑刀 |
Translated |
|
|
CNS 6151
2017 Edition Method of Test for Electromechanical SwITches(Overload) 電機開關檢驗法–過負荷 |
|
| Find out:3948Items | To Page of: First -Previous-Next -Last | [86] [87] [88] [89] [90] [91] [92] |
