"It " CNS Standards List |
|
CNS 14819
2017 Edition Method of test for surface flammabilIty of materials using a radiant heatenergy source 材料表面耐燃燒性試驗法-輻射熱源垂直試驗法 |
|
|
|
CNS 2864
2017 Edition Deep Groove Thrust Ball Bearings Single-Thrust, wIth Flat Seating 深溝止推滾珠軸承（單向具平面座外環） |
|
|
|
CNS 14820
2017 Edition Method of test for measuring toxic gases generated by solid material flammabilIty － Gas detector tube 固體材料燃燒毒性氣體濃度試驗法－檢測管法 |
|
|
|
CNS 12295
2017 Edition General Rules for ReliabilIty Assured Power Type Fixed Wire Wound Resistors 可靠度保證功率型線繞固定電阻器總則 |
|
|
|
CNS 4589
2017 Edition General Rules of Fixed CapacItors for Use in Electronic Equipment 電子設備用固定電容器通則 |
|
|
|
CNS 9110
2017 Edition Symbols of Bus - Bar of Interior Wiring Diagram for ArchItectural Plans 屋內配線設計圖滙流排槽類符號 |
|
|
|
CNS 13808
2017 Edition EpItaxial Wafers for Light Emitting Diodes 發光二極體磊晶片 |
|
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings wIth Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 13394
2017 Edition Method of Test for ViscosIty of Pulp (Falling Ball Method) 紙漿黏度試驗法（落球法） |
Translated |
|
|
CNS 15429-2
2017 Edition Banking - Secure cryptographic devices (retail) - Part 2: SecurIty compliance checklists for devices used in financial transactions 銀行業－零售式安全密碼裝置－第2部：使用於金融交易裝置之安全遵循查檢表 |
|
|
|
CNS 6154
2017 Edition Method of Test for Electromechanical SwItches(High/Low Temperature Operation) 電機開關檢驗法–高低溫操作 |
|
|
|
CNS 318
2017 Edition AC CircuIt Breakers (for Short Circuit Test) 交流斷路器標準（短路試驗用） |
|
|
|
CNS 13126
2017 Edition Metallic and Other Non-2organic Coatings -General Rules for Corrosion Tests Applicablc for Storage CondItionss 金屬和無機被覆–儲存狀態下之腐蝕試驗通則 |
|
|
|
CNS 7058
2017 Edition Method of Test for FlammabilIty of Textile Floor Coverings - Hot Metal Nut Method 地毯類織物防焰性試驗法（熱金屬螺帽法） |
|
|
|
CNS 4221
2017 Edition Metric Trapezoidal Screw Thread (LimIts for Internal Screw Threads From 8mm to 100mm) 梯形螺紋（標稱直徑８ｍｍ至１００ｍｍ的內螺紋限界尺寸） |
|
|
|
CNS 4844
2017 Edition Heavy Type Hexagon Head Pipe Plugs wIth Shoulder, Vent Hole and Parallel Thread 重型六角頭管塞（具肩部、通氣孔與平行螺紋） |
|
|
|
CNS 11101
2017 Edition Method of Test for Electromechanical SwItches-Transmittancy (Luminance) 電機開關檢驗法–傳導度（亮度） |
|
|
|
CNS 3455
2017 Edition Method of test for milk and milk products - Determination of viscosIty in condensed milk 乳品檢驗法－煉乳黏度之測定 |
|
|
|
CNS 12807
2017 Edition QualIty Requirement for Microfilm of Documents and Drawings 微縮品製作–文件及圖面微縮軟片品質之要求 |
|
|
|
CNS 4216
2017 Edition Wire Twister Pliers (wIth Side Cutter) 扭絲鉗（附邊剪器） |
Translated |
|
|
CNS 9112
2017 Edition Symbols of Telephone and Bell of Interior Wiring Diagram for ArchItectural Plans 屋內配線設計圖電話、電鈴類符號 |
|
|
|
CNS 11875
2017 Edition Fixed Mica CapacItors (Type CM 50) 雲母固定電容器（ＣＭ５０型） |
|
|
|
CNS 7002
2017 Edition Machine Taper Pin Reamers wIth Parallel Shanks 推拔銷鉸刀（圓柱柄，機用） |
|
|
|
CNS 12122
2017 Edition Method of Test on Communication Receivers for AmplItude-Modulation Transmissions 調幅通信接收機檢驗法 |
|
|
|
CNS 5820
2017 Edition Silica Powder (WhIte Carbon) (for Rubber Use) 二氧化矽粉（橡膠用） |
Translated |
|
|
CNS 4845
2017 Edition Light Type Hexagon Head Pipe Plugs wIth Shoulder and Parallel Thread 輕型六角頭管塞（具肩部與平行螺紋） |
|
|
|
CNS 10694
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Characteristics of the Measuring Equipment and Reference SensItivity) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（測量設備之特性及基準靈敏度） |
|
|
|
CNS 13513
2017 Edition Mortar for UnIt Masonry 磚、石墁砌用墁料 |
|
|
|
CNS 4476
2017 Edition Slotted Set Screws wIth Cup Point 有槽無頭杯形端固定螺釘 |
|
|
|
CNS 9107
2017 Edition Symbols of Connecting of Interior Wiring Diagram for ArchItectural Plans 屋內配線設計圖連接類符號 |
|
| Find out:3948Items | To Page of: First -Previous-Next -Last | [86] [87] [88] [89] [90] [91] [92] |
