"It " CNS Standards List |
|
CNS 11707
2017 Edition Method of Test for Fiber Optic Devices (FOTP-51 Pulse Distortion Measurement of Multimode Glass Optical Fiber Information Transmission CapacIty) 光纖組件檢驗法（多模式玻璃光纖資訊傳輸容量之脈波失真測量ＦＯＴＰ–５１） |
|
|
|
CNS 1201
2017 Edition Knife File for SmIth 鐵工用刀形銼 |
Translated |
|
|
CNS 15322
2017 Edition Information technology - Radio frequency identification (RFID) for Item management - Data Protocol : application interface 資訊技術－品項管理之無線射頻識別－資料協定：應用介面 |
|
|
|
CNS 6006
2017 Edition Dimensions of HItch for Power Tillers 耕耘機用接頭 |
|
|
|
CNS 13653
2017 Edition Lot-Control Testing for Light EmItting Diode(for Communication) 通信用發光二極體之批品質控制測試 |
|
|
|
CNS 5501
2017 Edition Self - Aligning Ball Bearings: Wide Inner Race, Inner Race wIth Clamping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings wIth Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 4700
2017 Edition Hexagon Head Bolts wIth Thread Approximately to Head and with Small Widths Across Flats 六角頭全螺紋螺栓（具小對面寬度） |
|
|
|
CNS 1208
2017 Edition Heavy Triangular File for SmIth 鐵工用重式三角銼 |
Translated |
|
|
CNS 13347
2017 Edition Method of Test for AcrylonItrile - Butadiene - Styrene (ABS) Plastic Fittings for Water Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管接頭配件檢驗法 |
|
|
|
CNS 4253
2017 Edition SplIt Taper Pins 開口推拔銷 |
|
|
|
CNS 13217
2017 Edition Cold Rolled High Strength Steel Sheets wIth Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 13982-8
2017 Edition Methods of test for bulk down and feather − Part 8: Determination of fill power wIth steam conditioning 羽絨羽毛試驗法－第8部：蒸汽處理後蓬鬆度測定法 |
|
|
|
CNS 4360
2017 Edition Slotted Pan Head Screws wIth Small Head 有槽小盤頭螺釘 |
Translated |
|
|
CNS 10050
2017 Edition Methods of Measurement for Noise EmItted by Wood Working Machinery 木工機械噪音檢驗法 |
|
|
|
CNS 15091-8
2017 Edition Method of test for deep sea water - Determination of chlorinIty 深層海水檢驗法－氯之測定 |
|
|
|
CNS 2864
2017 Edition Deep Groove Thrust Ball Bearings Single-Thrust, wIth Flat Seating 深溝止推滾珠軸承（單向具平面座外環） |
|
|
|
CNS 11993
2017 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch CondItions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件ＦＯＴＰ–５０） |
|
|
|
CNS 4433
2017 Edition Round Nuts WIth Set Pin Hole in Side 側孔圓螺帽 |
|
|
|
CNS 5507
2017 Edition Rolling Bearings; Bearing wIth Spherical Outside Surface and Extended Inner Ring Width, Insert bearings 嵌入夾緊滾動軸承（具球面外環與加寬內環） |
|
|
|
CNS 11153
2017 Edition Method of Test for Effect of Organic ImpurIties in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 12292
2017 Edition ReliabilIty Assured Fixed Carbon Composition Resistors (Established Failure Rate) 可靠度保證混合碳固定電阻器（故障率設定） |
Translated |
|
|
CNS 12731
2017 Edition Method of Test for the Fluorescent Component of Brightness of Pulp, Paper and Paperboard QuantItatively 紙漿、紙及紙板之白度中螢光成分定量試驗法 |
Translated |
|
|
CNS 12850
2017 Edition Nodular GraphIte Iron Flanged Lift Check Valves (10 kgf/㎠) 球狀石墨鑄鐵凸緣升降型止回閥（10 kgf/㎠） |
Translated |
|
|
CNS 4419
2017 Edition Countersunk Square Bolts wIth Square Short Squore 平頂埋頭短方頸螺栓 |
|
|
|
CNS 12865-6
2017 Edition Method of Test for DigItal Microelectronics ( Terminal Capacitance ) 數位微電子檢驗法（端子電容值） |
|
|
|
CNS 4477
2017 Edition Slotted Set Screws wIth Cone End 有槽無頭錐形端固定螺釘 |
|
|
|
CNS 1204
2017 Edition Heavy Flat File for SmIth 鐵工用重式扁平銼 |
Translated |
|
|
CNS 1196
2017 Edition Half-round File for SmIth 鐵工用扁圓銼 |
Translated |
|
|
CNS 1206
2017 Edition Heavy Round File for SmIth 鐵工用重式圓銼 |
Translated |
| Find out:3948Items | To Page of: First -Previous-Next -Last | [88] [89] [90] [91] [92] [93] [94] |
