"T " CNS Standards List |
|
CNS 12615
2020 Edition MeThod of Test for Oxidation Stability of Aviation Fuels (Potential Residue Method) 航空燃油氧化穩定性試驗法（潛在殘餘物法） |
|
|
|
CNS 15200-5-11
2020 Edition MeThods of test for paints – Part 5-11: Mechanical property of film - Wet-Scrub resistance and cleanbility 塗料一般試驗法－第５－１１部：塗膜機械性質：耐擦洗性及耐洗淨性 |
|
|
|
CNS 625
2020 Edition STandard Classification of Fireclay Brick 耐火黏土磚分級標準 |
Translated |
|
|
CNS 9672
2020 Edition SloTted Truss(or Mushroom) Head Machine Screws 有槽蕈形頭小螺釘 |
|
|
|
CNS 15319-7
2020 Edition Sodium hydroxide for indusTrial use - Part 7: Determination of aluminum content 工業用氫氧化鈉－第７部：鋁含量測定法 |
|
|
|
CNS 1501
2020 Edition General Rules for Test Methods of Reagents 化學試藥試驗法通則 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 14626
2020 Edition CasT manganese steel crossings for switch and crossing work 錳鋼岔心 |
|
|
|
CNS 4486
2020 Edition FasTeners – Surface discontinuities – Bolts, screws and studs for general requirements 螺釘表面瑕疵 |
|
|
|
CNS 15344
2020 Edition SafeTy of machinery - Interlocking devices associated with guards - Principles for design and selection 機械安全－防護裝置之聯鎖裝備－設計與選擇原則 |
|
|
|
CNS 7298
2020 Edition MeThod of test for water absorptiveness of paper and board − Cobb method 紙及紙板吸水度試驗法－Cobb法 |
|
|
|
CNS 80000-1
2020 Edition QuanTities and Units − Part 1: General 量及單位－第1 部：通則 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or Thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 8409
2020 Edition Test method for resistance of anodic oxide coatings on aluminium and aluminium alloys to cracking by deformation 鋁及鋁合金之陽極氧化膜耐變形龜裂試驗法 |
|
|
|
CNS 8734
2020 Edition Spices and condimenTs − Chillies and capsicums, whole or ground (powdered) 香辛料及調味料－全果狀或粉狀番椒與辣椒 |
|
|
|
CNS 8407-2
2020 Edition Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Phosphoric-chromic acid solution immersion test method 鋁及鋁合金之陽極氧化膜封孔度試驗法－第２部：磷酸－鉻酸溶液浸漬試驗法 |
|
|
|
CNS 15319-9-1
2020 Edition Sodium hydroxide for indusTrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 9350
2020 Edition Bushes for Plain Bearings wiTh Lubrication Holes and Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 5038
2020 Edition LaboraTory filter paper and method of test 化學分析用濾紙 |
|
|
|
CNS 9446
2020 Edition STeel drums - Non-removable head 鋼製圓桶－密蓋式 |
|
|
|
CNS 12835-4
2020 Edition PlasTics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 3: Fittings 燃氣用塑膠配管系統－聚乙烯(PE)－第4部：閥 |
|
|
|
CNS 15200-5-6
2020 Edition MeThods of test for paints – Part 5–6: Mechanical property of film - Adhesion test (Cross–cut test) 塗料一般試驗法－第５－６部：塗膜機械性質：附著試驗(方格法) |
|
|
|
CNS 5817
2020 Edition Rubber compounding ingredienTs − Carbon black − Determination of pellet size distribution 橡膠配合劑－碳黑－粒徑分布之測定 |
|
|
|
CNS 3220-1
2020 Edition SaniTary ceramic ware – Tank for water closet 衛生陶瓷器－ 水箱 |
Translated |
|
|
CNS 2352
2020 Edition STandard Classification of High-Alumina Brick 高鋁耐火磚分級標準 |
Translated |
|
|
CNS 17296-3
2020 Edition AddiTive manufacturing − General principles − Part 3: Main characteristics and corresponding test methods 積層製造－通則－第3部：主要特性及對應試驗法 |
|
|
|
CNS 14315
2020 Edition MeThods of test for bending fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 10305
2020 Edition Flared Tubing End ３７°油管喇叭口 |
|
|
|
CNS 7921
2020 Edition MeThod of test for spices and condiments – Determination of acid-insoluble ash 香辛料及調味料之檢驗法－酸不溶性灰分之測定 |
|
|
|
CNS 3742
2020 Edition FreighT containers - Coding,identification and marking 貨櫃之代碼、識別及標誌 |
|
| Find out:15111Items | To Page of: First -Previous-Next -Last | [88] [89] [90] [91] [92] [93] [94] |
