"W " CNS Standards List |
|
CNS 6153
2017 Edition Method of Test for Electromechanical SWitches(Mechanical Endurance) 電機開關檢驗法–機械耐久性 |
|
|
|
CNS 7997
2017 Edition Oil Tempered Chromium Vanadium Alloy Steel Wires for Valve Spring 閥彈簧用油回火鉻釩合金鋼鋼線 |
|
|
|
CNS 11573
2017 Edition Method of Test for LoW Frequency (Below 3MHz) Electrical Connectors (TP-50 Sand and Dust Test) 頻率３ＭＨｚ以下電連接器檢驗法（細砂與塵埃試驗ＴＰ–５０） |
|
|
|
CNS 228
2017 Edition 60° Center Drills，Straight Form With Conical Protective Chamfer 中心鑽（60°，去角直線錐形） |
Translated |
|
|
CNS 12882
2017 Edition Method of Test for Hook DraWing Resistance of Cement Sack Paper Laminated with Plastic Woven Sheet 塑膠編織貼合水泥袋紙鈎裂強度試驗法 |
Translated |
|
|
CNS 14660-2
2017 Edition Acoustics - Determination of sound poWer levels of noise source using sound intensity - Part 2: Measurement by scanning 聲學─利用聲強測定噪音源聲功率位準─第二部：掃描量測 |
|
|
|
CNS 5968
2017 Edition Bronze ScreWed Lift Check Valves (10kgf/c㎡) 青銅螺紋口升降型止回閥（10 kgf/㎠） |
|
|
|
CNS 9803
2017 Edition Welding procedure qualification test for pressure vessels 壓力容器熔接施工方法之確認試驗 |
|
|
|
CNS 4250
2017 Edition Square Head ScreWs with Collar and Half Dog Point with Rounded End Screws 軸環半柱端方頭螺釘 |
|
|
|
CNS 9311
2017 Edition Method of test for colour fastness to carbonizing With sulphuric acid 耐硫酸碳化染色堅牢度試驗法 |
|
|
|
CNS 9109
2017 Edition Symbols of Wiring of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖配線類符號 |
|
|
|
CNS 4727
2017 Edition PoWer quality measurement in power supply systems − Part 1: Power quality instruments 動力插秧機 |
Translated |
|
|
CNS 4407
2017 Edition Curved Spring Washers for Screw Assemblies 波浪形彈簧墊圈（用於螺釘之組合） |
|
|
|
CNS 4896
2017 Edition Accuracy Inspection of Metal Cutting Vertical Band SaWing Machines 立式帶鋸機精度檢驗標準 |
Translated |
|
|
CNS 13403
2017 Edition Method of Ultrasonic Test for Seamless Steel and Electric Resistance Welded Steel Pipes and Tubes 無縫及電阻銲鋼管超音波檢測法 |
|
|
|
CNS 4305
2017 Edition Cross Recesses Pan Head Tapping ScreWs 十字穴盤頭自攻螺釘 |
|
|
|
CNS 4309
2017 Edition Conical Spring Washers 圓錐彈簧墊圈 |
|
|
|
CNS 4363
2017 Edition Slotted Countersunk (Flat) Head ScreWs for Fine Mechanics M 0.4 to M 1.4 精密用有槽平頂埋頭螺釘（標稱直徑自0.4mm至1.4mm） |
|
|
|
CNS 6151
2017 Edition Method of Test for Electromechanical SWitches(Overload) 電機開關檢驗法–過負荷 |
|
|
|
CNS 4487
2017 Edition Method of test for surface discontinuities –Bolts, screWs and studs for general requirements 螺釘表面瑕疵檢驗法 |
|
|
|
CNS 4482
2017 Edition Hexagon Socket Set ScreWs with Flat Point 六角承窩無頭平端固定螺釘 |
Translated |
|
|
CNS 4573
2017 Edition Slotted Raised Countersunk Bolts for DraWing Instruments 有槽扁圓頂埋頭螺栓（繪圖儀器用） |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings With Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 5502
2017 Edition Cylindrical Roller Bearings; With Ribs on Outer Ring, Single Row 滾柱軸承（單列具導肋外環） |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 8828
2017 Edition Hexagonal Wire netting 六角形鋼線網 |
|
|
|
CNS 660
2017 Edition Method of Test for Head Loss of Water Pumps 水泵工作位差檢驗法 |
|
|
|
CNS 12677
2017 Edition Method of Test for Qualification Procedure of Radiographic Testing Technique of Welds 熔接縫放射線透射試驗技術檢定之試驗法 |
|
|
|
CNS 15550
2017 Edition Guidelines for standards developers to address the needs of older persons and persons With disabilities 標準發展者考量年長者與 身心障礙者需求之指導綱要 |
|
|
|
CNS 9230
2017 Edition Method of Test for Dry Reed SWitches (Contact Life Testing) 乾式簧開關檢驗法（接觸點壽命試驗） |
|
| Find out:4878Items | To Page of: First -Previous-Next -Last | [88] [89] [90] [91] [92] [93] [94] |
