"0 " CNS Standards List| Air pumps | Acoustics | Method Test | Electronic data | Method Test | Instant coffee | Chisel | Method Test | |
|
CNS 13706
2018 Edition Circuit-Mode Bearer Services Categories of Integrated Services Digital Network (ISDN) 整體服務數位網路之電路式載送服務 |
|
|
|
CNS 13660-1
2018 Edition File Transfer, Access and Management (FTAM)-Part 1: Specification of Association Control Service Element (ACSE) Presentation and Session Protocol 檔案轉送、存取及管理–第１部分：結合控制服務元件、表現層及交談層協定規格 |
|
|
|
CNS 13302
2018 Edition Method of Ultrasonic Examination for Gas Pressure Welds of Reinforcing Deformed Bars 鋼筋混凝土用竹節鋼筋瓦斯壓接部超音波探傷試驗法 |
|
|
|
CNS 4106
2018 Edition Hydraulic Cylinders Internal Diameters and Piston Rod Diameters 液壓缸之內徑及活塞桿直徑 |
|
|
|
CNS 13010
2018 Edition Stainless steel tubular cored wires and rods for arc welding 電弧銲接用不銹鋼包藥銲線及包藥填料棒 |
|
|
|
CNS 14700
2018 Edition Generic functional architecture of transport networks 傳送網路之一般功能架構 |
|
|
|
CNS 15620-5
2018 Edition Insulation coordination for equipment within low-voltage system – Part 5: Comprehensive method for determining clearance and creepage distances equal to or less than 2 mm 低電壓系統下設備之絕緣協調－第5 部： 決定2 mm 以下空間距離及沿面距離之詳盡方法 |
|
|
|
CNS 15704-1
2018 Edition 7/24 taper spindle noses for automatic tool changers – Part 1: Dimensions and designation of spindle noses of forms S and SF 自動換刀器用7/24 錐度之主軸鼻端－第1 部：S 型及SF 型主軸鼻端之尺度及標示 |
|
|
|
CNS 13660-5
2018 Edition File Transfer,Access and Management (FTAM)-Positional File Access Service (flat) 檔案轉送、存取及管理–第５部分：攤平式位置檔案存取服務 |
|
|
|
CNS 15660-7
2018 Edition Test conditions for numerically controlled turning machines and turning centres − Part 7: Evaluation of contouring performance in the coordinate planes 數值控制車床及車削中心機之試驗條件－第7 部：座標平面上循跡性能評估 |
|
|
|
CNS 11503
2018 Edition Lifebuoy self-igniting lights 救生圈之自燃燈 |
|
|
|
CNS 10319
2018 Edition Method of Test for Ferrite Cores for Inductors Transformers 變壓器及感應線圈用鐵心試驗法 |
|
|
|
CNS 15006
2018 Edition Flow-metering devices for connection to terminal units of medical gas pipeline systems 連接於醫療氣體管線系統終端單元之流量計裝置 |
|
|
|
CNS 16061
2018 Edition Burning behaviour of textile and textile products − Vocabulary 紡織品及其產品之燃燒行為－詞彙 |
|
|
|
CNS 16064
2018 Edition Low modulus adhesives for exterior tile finishing 外裝壁磚用低模數接著劑 |
|
|
|
CNS 8204
2018 Edition Deep groove ball bearings,single-row without filling notch, with tapered bore 徑向深溝滾珠軸承－單列、無填裝槽、具推拔孔 |
|
|
|
CNS 10207
2018 Edition Exit lights and emergency direction lights 出口標示燈及避難方向指示燈 |
|
|
|
CNS 15037-2
2018 Edition Walking aids manipulated by both arms - Requirements and test methods - Part 2: Rollators 雙臂操作步行輔具－要求及測試法－第２部：帶輪助行器 |
|
|
|
CNS 10636
2018 Edition Method of Test for Water Permeability of Packing Material 包裝材料透水度試驗法 |
|
|
|
CNS 300
2018 Edition 60° Center Holes, Forms R、A、B and C 中心孔（60°，R型、A型、B型及C型） |
|
|
|
CNS 10078
2018 Edition Distribution Boards (Simple Type, Below 125V) for Marine Use 船用分電箱（簡易型，１２５Ｖ以下） |
|
|
|
CNS 2840
2018 Edition Folding Chairs 分板折合椅 |
Translated |
|
|
CNS 6510
2018 Edition Method of test for meat and meat products - Determination of starch content 肉及肉製品檢驗法－澱粉含量之測定 |
|
|
|
CNS 15130-3-21
2018 Edition Tests on electric cables under fire conditions - Part 3-21 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Category A F/R 電纜之燃燒試驗－第３－２１部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ａ Ｆ／Ｒ |
|
|
|
CNS 15091
2018 Edition Method of test for deep sea water - General rule 深層海水檢驗法－總則 |
|
|
|
CNS 15200-1-3
2018 Edition Method of test for coatings − Part 1-3: General rule − Examination and preparation of test samples 塗料一般試驗法－第1-3部：通則－試樣檢查與製備 |
|
|
|
CNS 11808
2018 Edition Method of Test for Unsaturated Polyester Resin Putty 不飽和聚酯樹脂油灰檢驗法 |
Translated |
|
|
CNS 6280
2018 Edition Surgical Scissors 外科用剪刀 |
|
|
|
CNS 13610
2018 Edition Documentation-Presentation of Scientific and Technical Reports 科學與技術報告撰寫格式 |
|
|
|
CNS 15605-1
2018 Edition Plastics − Determination of refractive index 塑膠－受負荷下之撓曲溫度測定法－第１部：一般試驗法 |
|
| Find out:5722Items | To Page of: First -Previous-Next -Last | [90] [91] [92] [93] [94] [95] [96] |
