"O " CNS Standards List |
|
CNS 14294
2020 Edition MethOd for determination of resistance to sulfuric acid of dense shaped refractory products 緻密定型耐火製品抗硫酸性測定法 |
|
|
|
CNS 8769
2020 Edition Wrapped Bushes fOr Plain Bearings, Lubricating - Holes, Grooves, Indentations 滑動軸承用捲製軸襯之潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 5079
2020 Edition Gypsum Casting and MOlding Plaster 鑄用及模型用熟石膏 |
|
|
|
CNS 15344
2020 Edition Safety Of machinery - Interlocking devices associated with guards - Principles for design and selection 機械安全－防護裝置之聯鎖裝備－設計與選擇原則 |
|
|
|
CNS 8483
2020 Edition COntrol Cables for Motor - Cycle 兩輪機車用操縱線 |
Translated |
|
|
CNS 4670-25
2020 Edition Specified Items fOr Machine Tools - Surface Grinders (Reciprocating Table Type) 工具機規範之項目–平面磨床（往復台式） |
Translated |
|
|
CNS 2788
2020 Edition Fish Plates fOr Light Rails 輕型鋼軌用魚尾板 |
|
|
|
CNS 2306
2020 Edition White POrtland Cement 白色卜特蘭水泥 |
Translated |
|
|
CNS 61427-2
2020 Edition SecOndary cells and batteries for renewable energy storage − General requirements and methods of test − Part 2: On-grid applications 再生能源儲能用二次單電池及電池組－一般要求及試驗法－第2部：併網應用 |
|
|
|
CNS 7397
2020 Edition MethOd of test for fiber glass products 玻璃纖維製品檢驗法 |
|
|
|
CNS 9480
2020 Edition Tyres - COast-by methods for measurement of tyre-to-road sound emission 輪胎實車慣性滑行噪音測定法 |
|
|
|
CNS 9558
2020 Edition ROund-steel link chains for hoisting equipments, calibrated, tested, short linked 起重設備用圓鋼製短環環鏈 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (GeOmetrical Tolerancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 151
2020 Edition Semi - Finished Washers (fOr Hexagonal Bolts and Nuts: M1 -M20) 半光（輾光）製墊圈（用於六角螺釘及螺帽Ｍ１至Ｍ２０） |
Translated |
|
|
CNS 8412
2020 Edition Test methOds for stress corrosion cracking on aluminium alloys 鋁合金之應力腐蝕龜裂試驗法 |
|
|
|
CNS 4670-20
2020 Edition Specified Items fOr Machine Tools - Gear Shapers (Pinion Cutter Type) 工具機規範之項目–齒輪刨製機（齒輪刨刀型） |
|
|
|
CNS 11081
2020 Edition MethOd for Calculating Heat Balancing of Cement Rotary Kiln 水泥工業用窯爐之熱平衡計算方法 |
|
|
|
CNS 8406-2
2020 Edition Test methOds for thickness of anodic oxide coatings on aluminium and aluminium alloys - Part 2：Eddy current method 鋁及鋁合金之陽極氧化膜厚度試驗法－第２部：渦電流試驗法 |
|
|
|
CNS 14104-3
2020 Edition PrOsthetics and orthotics - Limb deficiencies - Part 2: Method of describing lower limb amputation stumps 義肢學與矯具學－肢體缺陷－第３部：上肢截肢之描述 |
|
|
|
CNS 14868
2020 Edition IrOn chloride (Ⅱ) for waste water 廢水用氯化鐵（Ⅱ） |
|
|
|
CNS 9747
2020 Edition MethOd of Test for Fineness of Portland Cement by the Turbidimeter 卜特蘭水泥細度檢驗法（濁度計法） |
|
|
|
CNS 15200-5-10
2020 Edition MethOds of test for paints – Part 5–10: Mechanical property of film - Abrasion resistance (Reciprocating test panel method) 塗料一般試驗法－第５－１０部：塗膜機械性質：耐磨耗性(試片往復法) |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized Or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 15317-2
2020 Edition CrOsslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 2: Pipes 冷熱水輸送用交連聚乙烯管－第２部：管 |
|
|
|
CNS 1282
2020 Edition Leather - Physical and mechanical tests - DeterminatiOn of water resistance of flexible leather 皮革－物性及機械性質測試－耐水度試驗法 |
|
|
|
CNS 616
2020 Edition MethOd of Test for Cold Crushing Strength of Refractory Bricks 耐火磚抗壓強度試驗法 |
|
|
|
CNS 14668
2020 Edition MethOd of test for freezing point of aviation fuels(automatic phase transition method) 航空燃油凝固點相轉移自動測定法 |
|
|
|
CNS 15820-2
2020 Edition Electric mOtorcycles − Safety specifications − Part 2: Protection against hydrogen hazards for motorcycles fuelled with compressed hydrogen 電動機車－安全規範－第2 部：防止氫氣危害 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methOds for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 9349
2020 Edition Bushes fOr Plain Bearings Made From Copper Alloys, Solid 滑動軸承軸襯–銅合金製整件 |
|
| Find out:15086Items | To Page of: First -Previous-Next -Last | [90] [91] [92] [93] [94] [95] [96] |
