"N,N " CNS Standards List |
|
CNS 12235
2020 Edition Series 1 freight containers - Handling and securing 第一類貨櫃－裝卸及固定 |
|
|
|
CNS 10895
2020 Edition Vocabulary of metrology − Basic and general concepts and associated terms (VIM) 計量學詞彙－基本與一般概念及相關用語 |
|
|
|
CNS 12938
2020 Edition Vitrified clay pipes and fittings and pipe joints for drains and sewers 排水及污水用瓷化黏土管以及其配件與管接頭 |
|
|
|
CNS 6752
2020 Edition Glossary of Terms Relating to Parts of Metal Sawing Machines 鋸床、切斷機主要零件詞彙 |
|
|
|
CNS 3589
2020 Edition Air-Entraining Additions for Use in The Manufacture of Air-Entraining Portland Cement 輸氣卜特蘭水泥製造用輸氣添加劑 |
|
|
|
CNS 9075
2020 Edition Retaining rings-uniform section C type Ｃ型同心扣環 |
|
|
|
CNS 4372
2020 Edition Round Thread with Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 5394
2020 Edition Hooks 吊鉤 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 1859
2020 Edition Phloroglucinol (1,3,5-Trihydroxybenzene) 化學試藥（１，３，５苯三酚） |
|
|
|
CNS 6216
2020 Edition High purity n-hexane 高純度正己烷 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 62282-3-201
2020 Edition Fuel cell technologies − Part 3-201: Stationary fuel cell power systems − Performance test methods for small fuel cell power systems 燃料電池技術－第3-201部：定置型燃料電池發電系統－小型燃料電池發電系統之性能試驗法 |
|
|
|
CNS 8988
2020 Edition Chemical Reagent(Dry Loss Determination) 化學試藥（乾失量測定） |
|
|
|
CNS 2026
2020 Edition Trichloroacetic Acid 化學試藥（三氯醋酸） |
|
|
|
CNS 3221
2020 Edition Methods of test for Sanitary ceramic wares 衛生陶瓷器檢驗法 |
Translated |
|
|
CNS 14314
2020 Edition Method of test for particle density of fine ceramic powder 精密陶瓷粉末粒子密度測定法 |
|
|
|
CNS 11523
2020 Edition Method of Test for High - Temperature Fiber Blanket Thermal Insulation 高溫絕熱纖維氈檢驗法 |
|
|
|
CNS 9350
2020 Edition Bushes for Plain Bearings with Lubrication Holes and Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 14964-22
2020 Edition Wheelchair − Part 22: Set-up procedures 輪椅－第22部：設定程序 |
|
|
|
CNS 5561-2
2020 Edition High Tension Cable Connection for Ignition Coils and Distributors for Automobiles 汽車用點火線圈及分電盤用高壓接線端子 |
|
|
|
CNS 3-9
2020 Edition Engineering Drawing(Symbols for Hydraulic and Pneumatic Power Systems) 工程製圖（液壓系氣壓系製圖符號） |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 15344
2020 Edition Safety of machinery - Interlocking devices associated with guards - Principles for design and selection 機械安全－防護裝置之聯鎖裝備－設計與選擇原則 |
|
|
|
CNS 157
2020 Edition Square Taper Washers (for I Sections) 方形推拔墊圈（工字鐵用） |
|
|
|
CNS 14104-5
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 4: Description of causal conditions leading to amputation 義肢學與矯具學－肢體缺陷－第５部：截肢病患臨床狀態之描述 |
|
|
|
CNS 5270-2
2020 Edition Graphical Symbols for Fluid Power Diagrams-Pump and Motor 液壓、氣壓圖形符號–泵及馬達 |
|
|
|
CNS 705
2020 Edition Method of Test for Volcanic Ash for General Use 火山灰（一般用）檢驗法 |
|
|
|
CNS 15354
2020 Edition Test methods for dielectric strength of anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之陽極氧化膜絕緣性試驗法 |
|
|
|
CNS 5700
2020 Edition Glossary of Terms for Rolling Bearings 滾動軸承名詞 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [92] [93] [94] [95] [96] [97] [98] |
