"In " CNS Standards List |
|
CNS 15754
2019 Edition Plastics pipIng systems for non-pressure underground drainage and sewerage − Polyethylene (PE) 建築物內污水排放塑膠配管系統－聚乙烯(PE) |
|
|
|
CNS 16121-2
2019 Edition Electrical apparatus for the detection of combustible gases In domestic premises − Part 2: Electrical apparatus for continuous operation in a fixed installation in recreational vehicles and similar premises − Additional test methods and performance requir 家居處所可燃氣體偵測用之電氣裝備－第2部：固定裝設於休旅車船及類似處所之持續操作用電氣裝備－附加試驗方法及性能要求 |
|
|
|
CNS 14826
2019 Edition Lightweight aggregates for Insulating concrete 隔熱混凝土用輕質粒料 |
|
|
|
CNS 15748-4
2019 Edition Integrated Circuits – Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 4: Measurement of conducted emissions – 1 Ω/150 Ω direct coupling method 積體電路－150 kHz 至1 GHz 電磁放射量測－第4 部：傳導放射量測－1Ω/150Ω直接耦合法積體電路－150 kHz 至1 GHz 電磁放射量測－第4 部：傳導放射量測－1Ω/150Ω直接耦合法 |
|
|
|
CNS 15665
2019 Edition Long durable paInts for steel structures 鋼構用長期耐候性塗料 |
|
|
|
CNS 16102
2019 Edition Specification and qualification of weldIng procedures for metallic material − Qualification based on pre-production welding test 金屬材料銲接程序規範書及其檢定－依〝製造前銲接試驗〞檢定 |
|
|
|
CNS 13602
2019 Edition General construction of gas burnIng appliances for domestic use 家庭用燃氣燃燒器具構造通則 |
|
|
|
CNS 5808
2019 Edition Methods of Test for Strength Properties of Adhesives for Wood In Shear by Tension Loading 木材用黏著劑之抗剪強度測定法（拉力負荷法） |
|
|
|
CNS 3304
2019 Edition TestIng Standard for Performance of Internal Combustion Engines for Marine Use 船用內燃發動機性能檢驗標準 |
|
|
|
CNS 5129
2019 Edition MeasurIng Methods for Electrical Resistivity and Conductivity of Non-Ferrous Materials 非鐵金屬材料之體積電阻係數及導電率測定法 |
|
|
|
CNS 4269
2019 Edition Hot-rolled atmospheric corrosion resistIng steels for welded structure 銲接結構用耐候性熱軋鋼料 |
|
|
|
CNS 15762-3
2019 Edition Footwear − Test methods for uppers − Part 3: Colour fastness to rubbIng of uppers, linings and insocks 鞋類－鞋面試驗法－第3 部：鞋面、內裡及鞋墊之摩擦色牢度 |
|
|
|
CNS 16107-4
2019 Edition Hollow taper Interface with flange contact surface − Part 4: Dimensions of receivers for stationary tools 具凸緣接觸面之空心錐度界面－第4部：固定式刀具用接收器之尺度 |
|
|
|
CNS 16107-3
2019 Edition Hollow taper Interface with flange contact surface − Part 3: Dimensions of shanks for stationary tools 具凸緣接觸面之空心錐度界面－第3部：固定式刀具之刀柄尺度 |
|
|
|
CNS 8579
2019 Edition Glossary of Terms RelatIng to Electric Equipment for Automobiles(Wiring Harness) 汽車用電器零件詞彙（配線束） |
|
|
|
CNS 5611
2019 Edition General prInciples of physical testing methods for textiles 紡織品物理試驗法通則 |
|
|
|
CNS 20349-2
2019 Edition Personal protective equipment − Footwear protectIng against risks in foundries and welding − Part 2: Requirements and test methods for protection against risks in welding and allied processes 個人防護具－防止鑄造及熔接中風險之鞋類－第2部：防護熔接及類似製程風險之要求事項及試驗方法 |
|
|
|
CNS 11359
2019 Edition Polyethylene - alumInum - polyethylene pipes for water works 聚乙烯(交連聚乙烯)絕緣聚氯乙烯(聚乙烯)被覆耐火電纜 |
|
|
|
CNS 14545-8
2019 Edition Fire hazard testIng-Part 2:Test methods-Section 2:Needle-flame test 火災危險性試驗－第２部：試驗方法－第２章：針焰試驗 |
|
|
|
CNS 15104
2019 Edition Textiles - DetermInation of abrasion resistance of fabrics by the Martindale method - Part 2 : Determination of specimen breakdown 紡織品耐摩損性馬丁代爾試驗法－第２部:試樣耐摩損試驗法 |
|
|
|
CNS 14958-1
2019 Edition Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Human models, Instrumentation, and procedures – Part 1: Procedure to determine the specific absorption rate (SAR) for hand-held devices used in close 人體曝露於手持式及佩戴式無線裝置之射頻場－人體模型、儀器及程序－第１部︰使用時靠近耳朵之手持式裝置（頻率介於３００ＭＨｚ至３ＧＨｚ）之比吸收率（ＳＡＲ）量測程序 |
Translated |
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker In low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 2770-8
2019 Edition Method of Test for Feeds : DetermInation of Crude Fiber 飼料檢驗法（粗纖維之測定） |
Translated |
|
|
CNS 15748-5
2019 Edition Integrated circuits – Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 5: Measurement of conducted emissions – Workbench Faraday Cage method 積體電路－150 kHz 至1 GHz 電磁放射量測－第5 部：傳導放射量測－工作台法拉第箱體法 |
|
|
|
CNS 11013
2019 Edition Iron and steel－Methods for determInation of silicon content 鐵及鋼－矽定量法 |
|
|
|
CNS 5809
2019 Edition Methods of Test for Strength Properties of Adhesives In Shear by Compression Loading 黏著劑之抗剪強度測定法（壓縮負荷法） |
|
|
|
CNS 9027
2019 Edition Method of Test for Feed Additives: DetermInation of Dibutyl Hydroxy Toluene(BHT) and Butyl Hydroxy Anisol(BHA) 飼料添加物檢驗法–二丁基羥基甲苯與丁基羥基甲氧苯之測定 |
|
|
|
CNS 1499
2019 Edition Textiles - Colour fastness to rubbIng 耐摩擦色牢度試驗法 |
Translated |
|
|
CNS 2316
2019 Edition TestIng Standard of Small Internal Combustion Engines for Marine Use 船用小型內燃發動機性能檢驗標準 |
Translated |
|
|
CNS 7408
2019 Edition Rigid cellular plastics – DetermInation of compression properties 硬質發泡塑膠－壓縮性能測定法 |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [93] [94] [95] [96] [97] [98] [99] |
