"I " CNS Standards List |
|
CNS 4539
2020 Edition Terms relatIng to the manufacture of fasteners 結件詞彙（製造方法） |
|
|
|
CNS 9480
2020 Edition Tyres - Coast-by methods for measurement of tyre-to-road sound emIssion 輪胎實車慣性滑行噪音測定法 |
|
|
|
CNS 5270-7
2020 Edition GraphIcal Symbols for Fluid Power Diagrams-Directional Control Valve 液壓、氣壓圖形符號–方向控制閥 |
|
|
|
CNS 8215
2020 Edition SteerIng Bearings for Motorcycles 機車用轉向軸承 |
|
|
|
CNS 9746
2020 Edition Method of Test for PotentIal Expansion of Portland Cement Mortars Exposed to Sulfate 卜特蘭水泥墁料暴露於硫酸盬中之潛在膨脹檢驗法 |
|
|
|
CNS 14579-1
2020 Edition Method of test for preventIon of fire for automobiles – Part 1: Fuel tanks 汽車火災預防檢驗法－第１部：燃料箱 |
|
|
|
CNS 4318
2020 Edition ISO Miniature Screw Threads-Tolerances 公制精細小螺紋公差（ＩＳＯ制） |
Translated |
|
|
CNS 1988
2020 Edition SodIum sulfide nonahydrate (Reagent) 九水合硫化鈉（試藥） |
|
|
|
CNS 1986
2020 Edition SodIum Sulfate, Anhydrous 化學試藥（無水硫酸鈉） |
|
|
|
CNS 1870
2020 Edition PIcks, Two Taper Ends 化學試藥（苦味酸） |
|
|
|
CNS 14315
2020 Edition Methods of test for bendIng fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 14566
2020 Edition Sleeper screws (Screw spIkes) 螺旋道釘 |
|
|
|
CNS 14475
2020 Edition Method of test for estImation of net heat of combustion of aviation fuels 航空燃油淨燃燒熱計算法 |
|
|
|
CNS 8988
2020 Edition ChemIcal Reagent(Dry Loss Determination) 化學試藥（乾失量測定） |
|
|
|
CNS 16145-2
2020 Edition CeramIc tiles − Grouts and adhesives − Part 2: Test methods for adhesives 陶瓷面磚－填縫劑與接著劑－第2部：接著劑試驗法 |
|
|
|
CNS 16144-1
2020 Edition Gas detectors − ElectrIcal apparatus for the detection of carbon monoxide in domestic premises − Part 1: Test methods and performance requirements 氣體偵測器－家居處所一氧化碳偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 120
2020 Edition Collar (UsIng Light Duty Set Screw) 頸圈（用螺絲銷、輕型） |
|
|
|
CNS 468
2020 Edition RIdge Type Cement Tiles 槽形水泥瓦 |
Translated |
|
|
CNS 15227
2020 Edition SIngle-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 8411-1
2020 Edition Test methods for abrasIon resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Wheel wear test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－ 第１部：磨輪磨耗試驗法 |
|
|
|
CNS 9597
2020 Edition SuspensIon Coil Springs for Automobiles 汽車用懸吊裝置螺旋彈簧 |
|
|
|
CNS 8028
2020 Edition ChemIcal Reagent (Hydrazinium (II) Dichloride) 化學試藥（二氯化 |
|
|
|
CNS 621
2020 Edition Method of Test for RefractorIness Under Load of Refractory Bricks 耐火磚荷重耐火度試驗法 |
|
|
|
CNS 15319
2020 Edition SodIum hydroxide for industrial use - General rule 工業用氫氧化鈉－總則 |
|
|
|
CNS 14104-3
2020 Edition ProsthetIcs and orthotics - Limb deficiencies - Part 2: Method of describing lower limb amputation stumps 義肢學與矯具學－肢體缺陷－第３部：上肢截肢之描述 |
|
|
|
CNS 14503-1
2020 Edition EvaluatIon methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 14242
2020 Edition Method of test for peroxIde number of aviation turbine fuels 航空燃油過氧化物值測定法 |
|
|
|
CNS 500
2020 Edition ISO Metric Fine Screw Threads (Diameters from 4 to 8mm and Pitches 0.5 to 0.75mm) 公制細螺紋3（ISO制）（標稱直徑4至8公釐，螺距0.5至0.75公釐） |
Translated |
|
|
CNS 10052
2020 Edition NomInal dimensions of veneer lathes 薄片木車床之標稱尺度 |
|
|
|
CNS 15804
2020 Edition OIl of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
| Find out:15020Items | To Page of: First -Previous-Next -Last | [94] [95] [96] [97] [98] [99] [100] |
