"Ply" CNS Standards List |
|
CNS 15010
2022 Edition Unplasticized high impact polyvinyl chloride (PVC-U) pipe fittings for general uses and water supPly 一般用與自來水用耐衝擊硬質聚氯乙烯塑膠管件 |
|
|
|
CNS 15010
2022 Edition Unplasticized high impact polyvinyl chloride (PVC-U) pipe fittings for general uses and water supPly 一般用與自來水用耐衝擊硬質聚氯乙烯塑膠管件 |
|
|
|
CNS 11668
2021 Edition Flame-retardant Plywood 防焰合板 |
|
|
|
CNS 11669
2021 Edition Fire-retardant Plywood 耐燃合板 |
|
|
|
CNS 11487
2021 Edition Method of Test for Wet Ply Separation of Corrugated Fiberboard 瓦楞紙板濕潤分層試驗法 |
|
|
|
CNS 12835-2
2021 Edition Plastics piping systems for the supPly of gaseous fuels – Polyethylene (PE) – Part 1: General 燃氣用塑膠配管系統－聚乙烯(PE)－第２部：管 |
|
|
|
CNS 15944
2021 Edition Electrical supPly track systems for luminaires 燈具用電源導軌系統 |
|
|
|
CNS 15882
2021 Edition Fancy veneer overlaid Plywood for structural use 天然木化粧單板結構用合板 |
|
|
|
CNS 15511-21-2
2021 Edition Electric vehicle conductive charging system − Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supPly − EMC requirements for off-board electric vehicle charging systems 電動車輛傳導式充電系統－第21-2部：電動車輛以傳導式連接至交流/直流電源的要求－非車載電動車輛充電系統的電磁相容要求 |
|
|
|
CNS 16127
2020 Edition Stationary a.c. and d.c. conductive power supPly systems for electric motorcycle − Standard interface for d.c. power supply systems 電動機車定置式交流及直流傳導式供電系統－直流供電系統介面 |
|
|
|
CNS 16126
2020 Edition Stationary a.c. and d.c. conductive power supPly systems for electric motorcycle − Battery swapping system 電動機車定置式交流及直流傳導式供電系統－電池交換系統 |
Translated |
|
|
CNS 16128
2020 Edition Stationary a.c. and d.c. conductive power supPly systems for electric motorcycle − Digital communication between electric motorcycle dedicated d.c. power supply device and electric motorcycle for control of d.c. charging 電動機車定置式交流及直流傳導式供電系統－電動機車專用直流供電裝置與電動機車間充電控制用數位通訊 |
|
|
|
CNS 16125
2020 Edition Stationary a.c. and d.c. conductive power supPly systems for electric motorcycle − General requirement 電動機車定置式交流及直流傳導式供電系統－一般要求 |
|
|
|
CNS 2456-2
2020 Edition Plastics piping systems for water supPly and for drainage and sewerage under pressure − Polyethylene (PE) − Part 1: General 壓力下給水、排水及排污用塑膠配管系統—聚乙烯(PE)—第2部：管 |
|
|
|
CNS 15274
2020 Edition Equipment for water supPly service - Method of test for effect to water quality 自來水用器具－對水質影響試驗法 |
|
|
|
CNS 2456-5
2020 Edition Plastics piping systems for water supPly and for drainage and sewerage under pressure − Polyethylene (PE) − Part 3: Fittings 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 15423-6
2020 Edition Equipment for water supPly service – Part 6: Test methods of durability 自來水用器具－第6部：耐久試驗法 |
|
|
|
CNS 2456-1
2020 Edition Plastics piping systems for the supPly of gaseous fuels − Polyethylene (PE) − Part 5: Fitness for purpose of the system 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第1部：通則 |
|
|
|
CNS 15423-1
2020 Edition Equipment for water supPly service – Part 1: Test methods of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 2456-3
2020 Edition Plastics piping systems for water supPly and for drainage and sewerage under pressure − Polyethylene (PE) − Part 2: Pipes 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 1815
2020 Edition Plywood vocabulary 化學試藥（硫酸對甲基胺基酚） |
|
|
|
CNS 15423-2
2020 Edition Equipment for water supPly service– Part 2: Test methods of low temperature resistant 自來水用器具－第2部：耐寒試驗法 |
|
|
|
CNS 15423-5
2020 Edition Equipment for water supPly service – Part 5: Test methods of destruction by vacuum pressure 自來水用器具－第5部：負壓破壞試驗法 |
|
|
|
CNS 15423-3
2020 Edition Equipment for water supPly service – Part 3: Test methods of water hammer 自來水用器具－第3部：水鎚試驗法 |
|
|
|
CNS 15791
2020 Edition SupPly and exhaust pipes for burning appliances 燃氣器具用供排氣管 |
|
|
|
CNS 15423-4
2020 Edition Equipment for water supPly service – Part 4: Test methods of prevention from back current 自來水用器具－第4部：逆流防止試驗法 |
|
|
|
CNS 12835-5
2020 Edition Plastics piping systems for the supPly of gaseous fuels − Polyethylene (PE) − Part 4: Valves 燃氣用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 12835-4
2020 Edition Plastics piping systems for the supPly of gaseous fuels − Polyethylene (PE) − Part 3: Fittings 燃氣用塑膠配管系統－聚乙烯(PE)－第4部：閥 |
|
|
|
CNS 12835-3
2020 Edition Plastics piping systems for the supPly of gaseous fuels – Polyethylene (PE) − Part 2: Pipes 燃氣用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 1349
2019 Edition Plywood 普通合板 |
Translated |
| Find out:74Items | To Page of: First -Previous-Next -Last | 1 2 3 |
