"Tall" CNS Standards List |
|
CNS 15542
2022 Edition Gas cylinders − Design, construction and testing of refillable composite gas cylinders and tubes − Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 L with non-load-sharing meTallic or non-metallic liners or without liners 氣瓶－可重填複合材料氣瓶與氣筒之設計、構造及測試－第3部︰450 L以下具不分擔負載金屬或非金屬內膽或無內膽之全包覆式纖維強化複合材料氣瓶與氣筒 |
|
|
|
CNS 15876-1
2022 Edition Specification and qualification of welding procedures for meTallic materials − Welding procedure tests − Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys 金屬材料銲接程序規範書及其檢定－銲接程序試驗－第1部：鋼的電弧銲接及氣銲、鎳及鎳合金的電弧銲接 |
|
|
|
CNS 4576
2022 Edition Bolted Connections with Reduced Body; Survey and InsTallation 減徑柄螺栓之結合法（概覽，應用範圍與裝用實例） |
|
|
|
CNS 15876-1
2022 Edition Specification and qualification of welding procedures for meTallic materials − Welding procedure tests − Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys 金屬材料銲接程序規範書及其檢定－銲接程序試驗－第1部：鋼的電弧銲接及氣銲、鎳及鎳合金的電弧銲接 |
|
|
|
CNS 15542
2022 Edition Gas cylinders − Design, construction and testing of refillable composite gas cylinders and tubes − Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 L with non-load-sharing meTallic or non-metallic liners or without liners 氣瓶－可重填複合材料氣瓶與氣筒之設計、構造及測試－第3部︰450 L以下具不分擔負載金屬或非金屬內膽或無內膽之全包覆式纖維強化複合材料氣瓶與氣筒 |
|
|
|
CNS 15814-1
2021 Edition Fire tests for building elements and components – Fire testing of service insTallations – Part 1: Penetration seals 建築構件與零組件防火試驗－配管設置防火測試－第1 部：貫穿填縫材料 |
|
|
|
CNS 15827-20
2021 Edition Safety rules for the construction and insTallation of lifts – Lifts for the transport of persons and goods – Part 20: Passenger and goods passenger lifts 升降機結構及安裝之安全總則－人員及貨物運輸用升降機－第20部：載人及運貨用升降機 |
|
|
|
CNS 3376-17
2021 Edition Electrical apparatus for explosive gas atmospheres - Part 17: Inspection and maintenance of electrical insTallations in hazardous areas (other than mines) 爆炸性氣體環境用電機設備－第１７部：安裝於危險區域電機設備之檢查和維護（不包含礦坑用） |
|
|
|
CNS 15878
2021 Edition Specification and qualification of welding procedures for meTallic materials − General rules 金屬材料銲接程序規範書及其檢定－通則 |
|
|
|
CNS 2394
2021 Edition Fire Clay Bricks for MeTallurgical Use 火黏土耐火磚（金屬冶煉用） |
Translated |
|
|
CNS 15230
2021 Edition Non-refillable meTallic gas canisters for portable liquefied petroleum gas appliances 不可再充填式金屬製攜帶用液化石油氣罐體 |
|
|
|
CNS 60335-2-51
2021 Edition Household and similar electrical appliances − Safety − Part 2-51: Particular requirements for stationary circulation pumps for heating and service water insTallations 家用和類似用途電器－安全性－第2-51 部：加熱及供水設備用的放置型循環泵之個別規定 |
|
|
|
CNS 15877-1
2021 Edition Specification and qualification of welding procedures for meTallic materials − Welding procedure specification – Part 1: Arc welding 金屬材料銲接程序規範書及其檢定－銲接程序規範書－第1 部：電弧銲接 |
|
|
|
CNS 15827-50
2021 Edition Safety rules for the construction and insTallation of lifts – Examinations and tests – Part 50: Design rules, calculations, examinations and tests of lift components 升降機結構及安裝之安全總則－檢驗及試驗－第50 部：升降機構件之設計規則、計算、檢驗及試驗 |
|
|
|
CNS 10880-25
2021 Edition Method of Test for Paint Components-Quantitative Test of MeTallic Zinc in Solvent Insolubles 塗料成分檢驗法–溶劑不溶物中金屬鋅之定量試驗 |
|
|
|
CNS 15822
2021 Edition MeTallic flexible hoses for gas 燃氣用金屬可撓性管 |
|
|
|
CNS 13629
2021 Edition Polybutylene (PB) plastics piping systems for hot and cold water insTallations - Part 7: Guidance for the assessment of conformity 聚碳酸酯成形材料 |
Translated |
|
|
CNS 15814-2
2021 Edition Fire tests for building elements and components – Fire testing of service insTallations – Part 2: Linear joint (gap) seals 建築構件與零組件防火試驗－ 配管設置防火測試－ 第2 部：線形接合(縫隙)密封部 |
|
|
|
CNS 60423
2021 Edition Conduit systems for cable management − Outside diameters of conduits for electrical insTallations and threads for conduits and fittings 電纜管理用導線管系統－電氣安裝用導線管外徑及導線管與配件用螺紋 |
|
|
|
CNS 15533-2
2021 Edition Safety requirements for secondary batteries and battery insTallations - Part 2: Stationary batteries 二次電池及電池安裝之安全性要求－第2部：定置型電池 |
|
|
|
CNS 15784-1
2021 Edition Low-voltage electrical insTallations − Part 1: Fundamental principles, assessment of general characteristics, definitions 低電壓電機裝備－第1 部：基本原則、一般特性之評估及定義 |
|
|
|
CNS 39
2021 Edition Operation of Handles and Indication of Electric InsTallations 電氣裝置手柄之操作及指示 |
|
|
|
CNS 15468-3-3
2021 Edition Fuel cell technologies – Part 3-3: Stationary fuel cell power systems – InsTallation 燃料電池技術－第3-3部：定置型燃料電池發電系統－設置 |
|
|
|
CNS 3376-14
2021 Edition Electrical apparatus for explosive gas atmospheres-Part 14: Electrical insTallations in hazardous areas (other than mines) 爆炸性氣體環境用電機設備－第１４部：危險區域之電機設備裝置（不包含礦坑用） |
|
|
|
CNS 15912
2021 Edition Design, manufacture, insTallation and testing of climbing nets and netting/mesh used in amusement rides, devices, play areas and attractions 遊戲場用攀爬網及安全網/格網之設計、製造、安裝及測試 |
|
|
|
CNS 13802-11
2021 Edition Graphical symbols for diagrams (Architectural and topographical insTallation plans and diagrams) 電機工程製圖符號（建築及地形學之裝置圖與製圖） |
|
|
|
CNS 15533-3
2021 Edition Safety requirements for secondary batteries and battery insTallations - Part 3: Traction batteries 二次電池及電池安裝之安全性要求－第3部：牽引用電池 |
|
|
|
CNS 22568-4
2021 Edition Foot and leg protectors − Requirements and test methods for footwear components − Part 4: Non-meTallic perforation resistant inserts 腳及腿保護器－鞋類構件之要求事項及試驗方法－第4部：非金屬耐踏穿片 |
|
|
|
CNS 22568-1
2021 Edition Foot and leg protectors − Requirements and test methods for footwear components − Part 1: MeTallic toecaps 腳及腿保護器－鞋類構件之要求事項及試驗方法－第1部：金屬護趾片 |
|
|
|
CNS 22568-2
2021 Edition Requirements and test methods for footwear components − Part 2: Non-meTallic toecaps 腳及腿保護器－鞋類構件之要求事項及試驗方法－第2部：非金屬護趾片 |
|
| Find out:201Items | To Page of: First -Previous-Next -Last | 1 2 3 4 5 6 7 |
