"Electrical Engineering " CNS Standards List |
|
CNS 666:2021
- English Version Bare hard-drawn single solid copper wire 裸硬銅單電線 - 英文版 |
|
|
|
CNS 102:2021
- English Version Scheduled Information to be Given on Enquiring and Ordering of Electric Machines (Small and Medium Size D.C. Generators) 詢價與訂購電機應開列之條款（中小型直流發電機） - 英文版 |
|
|
|
CNS 3993:2021
- English Version Method of Test for High Voltage Alternating Current Starters 高壓交流起動器檢驗法 - 英文版 |
|
|
|
CNS 11445-4:2021
- English Version Method for determining synchronous machine quantities from test 同步機電機參數試驗法 - 英文版 |
|
|
|
CNS 62933-1:2021
- English Version Electrical energy storage systems (EESS) − Part 1: Vocabulary 電能儲存系統(EESS)－第1部：詞彙 - 英文版 |
|
|
|
CNS 15530:2021
- English Version Methods of environmental test on light emitting diode systems (for general lighting service) 照明用發光二極體系統之環境試驗法 - 英文版 |
|
|
|
CNS 15511-21-2:2021
- English Version Electric vehicle conductive charging system − Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supply − EMC requirements for off-board electric vehicle charging systems 電動車輛傳導式充電系統－第21-2部：電動車輛以傳導式連接至交流/直流電源的要求－非車載電動車輛充電系統的電磁相容要求 - 英文版 |
|
|
|
CNS 14905-6:2021
- English Version Hand-held motor-operated electric tools - Safety - Part 2-6: Particular requirements for hammers 手持型電動工具－安全性－第２－６部：電鎚之個別規定 - 英文版 |
|
|
|
CNS 105:2021
- English Version Scheduled Information to be Given on Enquiring and Ordering of Electric Machines (Medium and Small Size A.C. Synchronous Motors) 詢價與訂購電機應開列之條款（中小型同步電動機） - 英文版 |
|
|
|
CNS 60335-2-81:2021
- English Version Household and similar electrical appliances − Safety − Part 2-81: Particular requirements for foot warmers and heating mats 家用和類似用途電器－安全性－第2-81 部：足部電暖器及電熱墊之個別規定 - 英文版 |
|
|
|
CNS 8795:2021
- English Version Method of Test for Copper Corrosion of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管銅腐蝕性試驗法 - 英文版 |
|
|
|
CNS 14905-3:2021
- English Version Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements for grinders, polishers and disk-type sanders 手持型電動工具－安全性－第２－３部：砂輪機、拋光機與盤式砂光機之個別規定 - 英文版 |
|
|
|
CNS 11445-9:2021
- English Version Noise limits of rotating electrical machines 旋轉電機之噪音限度 - 英文版 |
|
|
|
CNS 15357:2021
- English Version LED modules for general lighting - Safety specifications 一般照明用ＬＥＤ模組－安全性規範 - 英文版 |
|
|
|
CNS 15700-2:2021
- English Version Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories + Amendment 1 電源端插頭、電源端插座、車輛端插頭及車輛端插座－電動車輛傳導式充電－第2部：針對交流刃片及導電嘴配件之尺度相容性及互換性要求(補充增修1) - 英文版 |
|
|
|
CNS 8781:2021
- English Version General Rules for Testing of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管檢驗總則 - 英文版 |
|
|
|
CNS 13802-7:2021
- English Version Graphical Symbols for Diagrams (Switchgear,Controlgear and Protective Devices) 電機工程製圖符號（開關設備、控制設備及保護設備） - 英文版 |
|
|
|
CNS 60423:2021
- English Version Conduit systems for cable management − Outside diameters of conduits for electrical installations and threads for conduits and fittings 電纜管理用導線管系統－電氣安裝用導線管外徑及導線管與配件用螺紋 - 英文版 |
|
|
|
CNS 1373:2021
- English Version High-voltage (3.3kV) three-phase induction motors 高壓 (3.3kV) 三相感應電動機 - 英文版 |
|
|
|
CNS 5421:2021
- English Version Caculating methods of three-phase induction motor characteristics 三相感應電動機特性計算法 - 英文版 |
|
| Find out:2765Items | To Page of: First -Previous-Next -Last | [2] [3] [4] [5] [6] [7] [8] |
